Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
I have installed NCS V3.0.0, nrf54L05
I'm currently working on the ESB and BLE coexistence feature, but I've run into some issues.
In ,config file
I find that TIMER10...
Hello,
We have the following environment:
1) nRF Connect SDK v3.0.1
2) The custom board with nRF54H20
3) Our project with update capability using SUIT file.
...
I'm trying too use a timer as a counter on my nRF52840. This is the function in question:
static void timer_init ( void )
{
nrfx_timer_config_t timer_cfg = { ...
Hi NordicSemi
We might have mixed up different SoC versions of the nRF54L15.
According to the following page, there are different SDKs that supports different HW versions...
I want to evaluate Bluetooth LE Channel Sounding on the nRF54L15, using multiple antennas. The nRF54L15DK only has one antenna, so if I use it as both initiator and reflector...
I am experiencing issues programming my newly purchased nRF52840 DK, which has never been successfully flashed. After following the official starting guide on nordicsemi.com...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Hi everyone, I am attempting to configure two of NRF5340DK modules to execute ISO_Connected_Benchmark. I have tried to configure ipc_radio to compile for cpunet and application...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I would have a question regarding the use of PCAL6408A I/O expander on nRF9151 DK. The buttons and LEDs on nRF9151 DK are connected both directly to the processor...
We are planning to run a small proto build, and looking to program a small quantity of nRF54L10, prior to the SMT. These are loose parts (not built onto any PCBA). I am hoping...
I recently switched from evaluating an nRF52805 (Fanstel BC805M) to an nRF54L15 (using the nRF54L15-DK), and after I updated the toolchain and tried to flash the kit (using...
checking in if anyone is successfully using an open debug-probe for nRF54L series?
...guessing nordic is using segger OB on the DK's because of the Risc-V not fitting...
Hi,
I'm evaluating the nrf5340-DK board. I have a question about LED5 state. I tried following power sources:
usb J2, sw9 in VDD position - LED5 lights and I can detect...
