Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Dear Nordicsemi,
We are looking for Sub 1 GHz RF Module, which gives Longer Range distance in Field either in LOS or NLOS.
Please share the details regarding proven...
Hi guys,
We've written a small test on-top of our internal Bluetooth library (glorified wrapper sat on-top of SDK 15.2.0 SD140 6.1.1) on the nRF52840 to send dummy bulk...
Good morning everyone,
I am implementing a custom radio protocol on NRF52 without using the SoftDevice at the moment. For some reason, I get a HardFault which I am trying...
Hello everybody,
I can flash my custom nRF52832-based PCB using the nRF52 DK and Segger Embedded Studio or nrfjprog, but this requires that I always have my computer with...
Hi,
I need to get 1.8V on the VDD using high power mode. According to the documentation this is the default value. However, I measure 3V.
Please advise,
Daniel
I am developing a nRF-Mesh based product. This product consists of a fixed number of nodes in a Bluetooth Mesh Network. Are there possibilities to factory-provision a set...
Hi!
I am working with experimental_ble_app_eddystone in SDK 12.2.0 for nRF52.
I have seen that the firmware does not support using different advertising inteval for each...
I'm wondering whether or not nRF52840 can be used for a USB smart card development.
"According to the spec of a USB CCID device (which could be found on www.usb.org ), there...
Hello everyone,
After using IPSP intiator and IPSP Acceptor BLE Examples on 2 different kits and connecting them through this profile, how do i send IPv6 packets between...
I cannot get a connection between Seeger Studio and a dev board from Seed Studio called nRF52832-MDK
I have added a pull-down resistor on TDO as I was getting an error that...
is advertising Complete List of 128-bit Class UUIDs(0x07) a doable ? I mean like " Complete List of 16-bit Class UUIDs " (0x03) it's not a service, just has an information...
Hi,
I'm debugging a Nordic mesh example, which is named light_switch_server_nrf52832_xxAA_s132_6.0.0_Debug, after build and go, a message appear:
sd_ble_enable: app_ram_base...
Hi All,
Hoping this is straightforward for an intermediate developer.
nRF52840-DK (matched dongle not yet in use), SDK 15.2.0, SES 4.10a (Jlink 6.40), Windows 10.
My...
Hello,
I have seen that the nRF52840 PS v1.0 specifies the RSSI_PERIOD to be 15us. I have also seen that the nRF52832 has only a RSSI_PERIOD of 0.25us (PS v1.3+) or 8us...
