Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi all,
I have failed when try to flash a new softdevice s110 to the target device is Wunderbar's sensor module which is using nRF51822 chip. Flashing application has no...
Hello,
currently I am using the S110 Softdevice with the ble_template example as peripheral. This works fine.
For our final application, we need the central feature...
Question similar to this one
devzone.nordicsemi.com/.../
I have noticed that in the header ble.h included in the s310 folder, the function sd_ble_enable(..) and the type...
Hi Nordic expert, I wanna get a profile of 51822 performance cycle count. I found 51822 has no powerful DWT feature as cm3 or cm4, would you share me some feasible methods...
Hi All
I am aware that there are some changes to UV5.12 to do with Device Pack location etc.
I have currently updated my project from the .uvproj to .uvprojx extention...
I was able to setup gazell communication between two devices one as device and other as host using 32 byte payload size in nRf51822 module.
Here in gazell communication is...
We are using the Nordic Semi nRF51822-QFAC on our device for BLE. Since we are developing from scratch I understand we need have FCC testing done. Is there a summary of the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I had a nRF81522 design that was working at 3.3V and I dropped the voltage to 1.9V. I didn't change anything else, but now I am getting periodic disconnects during interogation...
I have a PCA 10028.
This board uses Two microcomputers.
One is N51422.
Another is microcomputer on which the seal is put(Segger ID:).
What is the role of this microcomputer...
I recently discovered this article ( mbientlab.com/.../) and am trying to understand the data transfer type between the firmware ( ble_app_hrs_s110_pca10028 ) and an iOS device...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
