On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
Hi,
I'm currently working with the Thingy:91X and would like to measure the total current consumption of the entire board using the PPK2. I understand that the PCA64165...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
While using the nRF9151 DK , after inserting the onomondo sim and connecting, the Cellular Monitor SIM sections appears the Wireless Logic ICCID number instead of onomondo...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
hi, i'm new in nrf module, i use nrf51822, i'm totly confuse what voltage that i should apply on DCC pin? if i want use internal dc/dc than what the voltage and if i use LDO...
after setting BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, I getting BLE_GAP_EVT_SEC_INFO_REQUEST event,
I am using same code as the sample:
case BLE_GAP_EVT_SEC_INFO_REQUEST...
Hi
I am using v6.0.0 softdevice S110 and SDK 5.1.0
In nrf_soc.h the function sd_temp_get() is defined.
The comments there say ..
"p_temp Result of temperature measurement...
Hi,
I use ble_s110_serialization sample code.
I try to notification many 20bytes(total 5KBytes) to my phone, I add some code in ble_app_hrs.
I follow this link to...
I used nRF_Demo_Utility ios app and WFConnector.framework in a sample testing app im building. And when I tried to archive it using xcode it invalidates it with a error message...
Hello,
I’m porting the hids_keyboard demo to work with the nrf51422 dev board. I just changed the #defines for the board in project settings, as well as the pin assignments...
Is there a way to change the scan interval while scanning is on?
I can stop scanning, set a different interval value and start again but that is not my intention, it wastes...
We have some nRF51 beacons kits and we want to connect some external peripherals using the available GPIO pins.
Does any one have an idea on how to solder some pin headers...
I'm trying to implement the ability to change the beacon properties (UUID, Major, Minor) using NRF Beacon Android app. My project is based on s110_nrf51822_7.0.0 (ble_app_beacon...
I'm working with the nRF51822, using the S110 soft device.
My application includes some measurement functions that are timing critical. Ideally, the code would be atomic...
Hi,
Can I use the J-Link Edu programmer to flash the nrf51822? Right now I'm using the J-Link LITE CortexM that I get from the development kit to flash the firmware into...
Hi folks,
I am struggling a little bit with Eclipse.
I just followed this tutorial ( embeddedsoftdev.blogspot.ca/.../eclipse.html) , the project compiles fine, but sometimes...
Hi everyone !!
I used to work with a RedBearLab module to prototype my bluetooth application, but since I have to plan the final version, I don't know which chip to choose...
I am using Eclipse Kepler, gcc and the nrf51 plugin ( sourceforge.net/.../) on OS X. I had an application that worked fine with SDK 5.2 and S110 Softdevice 6.0. I had been...
For my project，my ble device need to report firmware information to app， since the newer softdevices（like s130 0.5alpha） don't have FWID in UICR，where can I get it？
（Nrfgo...
