Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hello everyone,
I am trying to implement the OPTIGA Trust M from Infineon with the nrf9160. Unfortunately I encountered some problems regarding this topic.
I am trying...
Hi,
I'm working with the nrf52840, and I've had success with spi communication in the past. However, I want to switch to spim and am unsure how to do so. Can you provide...
Hey, Having some trouble getting the callbacks to invoke with the generic library on zephyr 1.7.1 to my understanding once it gets the data it should call it. have i misunderstood...
It is a very basic question.
For SOC firmware development with Segger and SDK, which layers of BLE are codes covering? Are Host and controller layers transparent to developers...
Hello,
Due to a routing error, the VBUS pin of the nRF52840 is connected to the GND.
The software works on the devkit but not on my prototype.
From what I saw in...
Hi！
Where master and slave is connecting, and then master is shutdown or move far away.Slave is wait for timeout.But the current of average slave e electric current
...
For my project I need to set the UART0 speed to 9600 baud.
So for testing I tried to compile the "Hello word" example by setting the board configuration file (ncs\v1.6.1...
CONFIGURACION:
NRF52 + SDK15 + SD132 + FREERTOS + NUS.
I have a task sending many packages to a central. I'm having an aboslutly aleatory behaviour: - At some time (could...
I’m checking the transaction of the data between iPhone and a Bluetooth device.
The device is developed by a business partner, but I’m not concerned the FW. I think we have...
Hi,
I am using nRf SDK5 and have a sensor that I am trying to extract the Eddystone UID data from the advertising packet. It shows up in nRfconnect as:
Eddystone UID...
I installed the nrf connect 3.91 with programmer v2.0.1 and J-Link driver v6.88a. However, when I cant seem to see the dev kit on my windows 10. I tried holding the reset...
Hi everyone,
I want to use the RTC module in my code, and I have some questions.
1. What I have understood so far is that the nRF52840 has three RTCs (RTC0, RTC1, RTC2...
Hello,
When using eDRX alone and without DATA (eDRX=81,92 sec, no PSM, no data transmittion,iDRX PDCCH = 1), it's showing an average current of 17,84 uA. This value is similar...
Hi Support team,
I have downloaded nRF5 SDK and found that there is a sample for serial via UART but however the samples ( <SDK Folder>\examples\peripheral\uart) is available...
Hi,
I've designed a product based on nrf52840 soc as a central Bluetooth device. I want to pair and connect to a Bluetooth device (as a slave) that implements a whitelist...
