When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
Got a Thingy91 (not the x model) that doesn't show up as anything when connected to a PC by USB, except when in bootloader mode, by pressing SW4 (no reaction with SW3) when...
I read other similar issues on this forum but they haven't helped solve my problem. I started with the peripheral_uart example project. Development and execution on the target...
Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
I have configured my application according to the Throughput example. The prj.conf file inside the sysbuild\ipc_radio folder is not being considered in the build. As a result...
Hello, everyone.
I would like to use mcumgr to update the firmware of a nrf52 via another nrf52 over uart.
From the documentation I understand that smp supports uart so...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
Hi! I am trying to get OSDP communication up and running on my nrf9160dk board. I am trying to run this sample: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples...
Hello,
I apologize if this is a simple question. I am working with the nRF9161-DK and am using the Serial LTE Modem application. The ultimate goal is to send data via...
I'm working on a Matter 1.3-compatible door lock with RFID credential management. I’ve enabled RFID support through the ZAP tool and configured the feature map accordingly...
Hi,
I am using the NCS Thread CLI sample as the base of my project and I was wondering if it's possible to disable the cli command functionalities of this project to save...
Hello,
I would like to keep track of time in Nordic Connect SDK (v1.9.1) based application.
The application has both BLE and Openthread enabled.
Before using Openthread...
