Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm transitioning from the old SDK to the ncs, and have been through the nRF Connect SDK Fundamentals and Bluetooth Low Energy Fundamentals courses.
With pairing...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
Hello, I am going through the Bluetooth Low Energy Fundamentals provided by Nordic.
My nrf 52840 dk could function fine after lesson1, but when I flash my board with the...
Hi，
For the SoftDevice controller， how can I send LL_MIN_USED_CHANNELS_IND messages？ Is there an API for this, or what scenarios trigger the sending of this message? Thanks...
Hello,
I'm measuring the power consumption on the Thingy:53 using the Debug and Current measurement board. Initially I was measuring the current of the battery VBAT given...
I have been using the VS Code extensions for setting up and building projects. Sometime yesterday build times went up from < 20 seconds to 10+ minutes. It looks like it's...
Hi,
I am starting a new development project on the nrf9160. It's a battery powered cell connected device using MQTT and Memfault.
Is it better to start a project from...
I need to measure the battery percentage using adc. i have created an application for ADC and its measuring correctly. Now i need to measure the battery percentage of another...
Hi,
I'm trying to measure message travel time using Gazel and k_uptime_get() so I can understand the packet intervals.
I'm using gzll_ack_payload_device and gzll_ack_payload_host...
Hello,
I am trying to control a PPK2 using my Raspberry Pi 3B+ running a 64-bit image of the Raspberry Pi OS (Debian Bookworm port) and I've been using python (v3.9) with...
Dear Nordic Team,
since the last release of NCS 2.7.0 the sd-card support breaks for me.
I am using the nrf5340 Audio DK with an inserted SD Card, and am running the zephyr...
Due to upgrading SDK2.5.0, I need to re-certify Thread1.3 in order to get a new CID for the previous module.Now I don't know exactly how to fill in the section of Thread Submission...
I have an application that requires invoking multiple commands to the same node in quick succession (multiple times a second).
To evaluate the feasibility of this, I flashed...
I am designing a pcb containing nrf52832. However, since I need a large number of GPIOs, I do not want to use the optional 32khz crystal in my circuit. But I also want to...
