Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I'm implementing LESC.
SDK version : 16.0.1
SD version : 7.0.1
example code : ble_app_hrs
I checked that the LESC(just works) function is working.
But...
I'm working on developing a UART Secure DFU platform on the NRF52833 with SDK 17.1 and soft-device s140 v7.2.0.
As there are no direct examples for this application, I followed...
Hi ,
I am new to this nRF5340. In peripherial UART , BLINKY, HELLO WORLD sample program is working fine. i need a support for DF CONNECTIONLESS RX &TX to enable bluetooth...
Hi,
on my Custom Board I'am setting P0.12 to High triggered by a BLE notification (NUS). I'am here using the BLE Uart Example (S112, pca10040). The Custom Board's nrf52832...
Hello,
i want to use the nrfSniffer in Windows. I updated the latest firmware (4.1.0) to the nRF52840 Dongle. I installed also the extcap Package to my personal folder....
Hello,
I would like to use the nRF52840 PDK version 0.9.0 at 1.8V VDD since my peripherals operate at 1.8V. At the same time, I would like to debug the DK through USB. ...
So I am working on ner52840 with nrf connect sdk, I need to scan a device which is broadcasting ble 5.0 extend advertising for a period of time(probably 2 second), then my...
Good morning.
I have an EVAL nRF52_DK PCA10040 V2.1.0 and connecting the EVAL to the PC through the USB cable no VCP and no CDC disc are recognized.
With an EVAL nRF52_DK...
i build the zephyr samples/hello_world Demo ,and it can run and print well on BOARD_NRF52840DK_NRF52840.
but this hex file cannot boot up on my own board.
for simplest...
In my nRF52810 based circuit board I'm trying to use the RTC along with the RTC tick interrupt to toggle an IO pin every 6msec. In main.c I use WFE to enter low power mode...
Hello!
I'm developing my own board featuring the nRF5340.
I wanted to add a PCB antenna to my layout and I figured the fastest way to create a functional prototype is...
Hello,
I noted that in the reference layout for nRF52832 CIAA with DC/DC converter there are VIP (Via-In-Pad) and blind via underneath the WLCSP package. I would like to...
