Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I am working on a custom board using the BC833M ( https://www.digikey.com/en/products/detail/fanstel-corp/BC833M/13174321 ) which uses an nRF52833. I am using a rigid...
Hi,
Customers have reported the problem of dfu upgrade failure, and we also use the same type of mobile phone (iPhone 11 & iPhone XR) for testing. It is found that there...
Hello,
I am relatively new to the nRF Connect SDK and I'm developing an application for nRF9160DK on toolchain version 2.0.2.
I am working on a non-secure application...
Hi, I am trying intialize the RTC in ncs using nrfx drivers and then connect it tick event to a saadc sampling event using a ppi channel. I learnt that RTC0 and RTC1 are used...
Hi
after create project from sample broadcast_audio_sink, when running it, i get following message:
[21:59:46:406] *** Booting Zephyr OS build v3.0.99-ncs1-2483-g482dcc7865f7...
I need to modify the code of different sensor data, which is obtained on LTE monitor, so I want that file in which I can create custom sensor data /Modify the sensor data...
Hello.
I had LC3 access granted.
I can access nrfconnect/sdk-lc3 on my web browser.
However, with bash, I get the following error and cannot build nRF5340_audio.
...
Hi Mate,
I have very small issue that is when i am trying to link config_bootloader_mcuboot=y in zephyr application the program is not flashed. I need to run zephyr application...
I was curious if there was a delta firmware update file to go from 1.3.1 to 1.3.0 on the nRF9160. Most of our business is in North America and we use a carrier who requires...
Hi all,
I'm trying to use the nrf Connect SDK and configure PWM to use in one pin from nordif nrf52DK. The final chip will be the nrf52810. I have configured the builder...
Hello,
I want to use pc-ble-driver WITH an EV-BT8400XE.
I develop with SDK15.3 (last compatible version of SDK for pc-ble-driver)
I am successfully able to use pc-ble...
Hey all together,
I'm using nrf Connect SDK 2.0.0 and want to place a variable in flash at a predefined location. The reason is, that I need to read the information stored...
Hi,
I'm setting up nRF Connect SDK according to this instruction ( http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html) and Getting Started...
Hey,
in our project the nrf is acting as the central and connecting phones.
As part of the connection process:
1) We check if the phone is bonded in the nrf.
2) We...
Hi,
I'm on NCS 1.8.0 and I've successfully built and run the peripheral_nfc_example sample. Printed logs when reading NDEF message using a smartphone
When I came to...
