Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
We want to check how changing system voltage affects on GPS reception, for that we need to know the RSSI of each satellite the model use.
I know I can get the C2N...
This is in reference to: devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader
On step B1, it says: " Next step, inside SDKFolder\external\micro...
Hi,
I'm working on a project where the NRF52840 chip is connected to multiple peripherals (4 of them) through SPI. The hardware has been designed in a way that each peripheral...
Hi, I am using the ant_plus/ant_bpwr/bpwr_rx code as a reference to capture power data from an SRM power meter. I am at the point where I get the following messages, which...
Title says most of it. I'm wanting to perform an OTA DFU of an nRF52840 running NCS 2.0.0 using my android from either the nRF Connect Device Manager or nRF DFU app. There...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...
I've got a working nrf52832 application using central role to connect to another peripheral. I also want to enable SMP DFU mode - so the app needs to advertise and behave...
Hi,
I am using sample code v1.8.0\zephyr\samples\net\sockets\dumb_http_server to test USB RNDIS
I did some changes in overlay-netusb.conf gile lik
# USB Device settings...
I'm interested in seeing what the NRF debug adapter does, using Jlink
2022.7.111 - nRF Connect for VS Code
I can't get it selected and the documentation is not very...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
hi,
I have a got a nrf9160dk and also a custom board built on nrf9160. I want to know which programmer to use for nrf9160dk first and subsequently can use it for testing...
Hello Nordic Team,
I was priting logs using RTT _LOG APIs
I can able to see timestamp while printing it
<t: 16775755>, main.c, 295, --------------------------------...
Hello Nordic Team,
I have a question out of curiosity.
BEACON debug prints has been enabled. And I am seeing these prints for every 10 seconds.
Below is the log
<t...
for the NRF9160 I have 256KB for RAM
however, only 128KB are available for my software, since it's defined as nr9160ns
how can I assign the full 256 kB for my software...
