Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
We are using nRFSDK v15.0.0 and nRF52840 in our system. There is also an external MCU that is connected to the nRF52840 via UART. Currently we are trying to perform...
Dear Members,
I want to use SDcard with softdevice, when I run fatfs_example()
I got this :
nfo> app: Initializing disk 0 (SDC)... rror> hardfault: HARD FAULT at...
Hello,
I've been working on a simple application to scan for bluetooth packets being emitted by another system, which advertises at a consistent 10Hz. We apply a filter...
Hi,
I try to do a OTA Update with watchdog enabled . The OTA Update runs and boots image B but this is stopped after watchdog timeout (1Sek). In my code the watchdog runs...
Hello all,
I am trying to develop an application where the user will input some specific commands i.e hex value of 0x01 via a mobile application and then via bluetooth this...
Hi,
I am migrating my code from sDK15 to SDK17. In SDK15 code app_timer_start() working fine with any timer value. But in SDK 17, I am getting error code 7.
When I debug...
Hai
I'm working on nrf52832 NFC, I have a few questions.
is NFC ID in nrf52832 is unique?
can I use it for payment purposes?
if that ID is not unique, any other solution...
Hello,
I am trying to use the **persistent** flash area of my nRF52.
I created a separate zone (PERSISTENT_FLASH) in my LD script as follows:
I try the following C...
Why is the pc-ble-driver-py version 0.16.2 released to pypi , but no according tag and release set in the github repository?
Is this a stable release already? And if so...
Hi
Problem description：
Disable the softdevice before writing uicr. After uicr is written, it fails to enable the softdevice again.
Can't softdevice be enabled again...
Hi I want to Integrate GPS(with A GPS assistance needed)with AWS iot example. when i start GPS on aws connect event ready .SUPL is initialized successfully and even SUPL socket...
Dear Nordic,
I'm using the nRF connect app for the smart phone to test BLE bonding.
I hope to know the bonding feature on the nRF connect app is working with Random...
Hi.
We've created a custom board, and it works nicely.
However, when I try to build another application for this new board (i.e. "Add Build Configuration"), the new board...
