When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Trying to flash firmware to nRF5340 cpuapp core with a sample from nRF connect sdk 1.6.1. I'm able to flash it to a PCA10095 dev kit. With EVM-BT40-V1 from Fanstel, I can...
Hi. I have came into trouble with nrfutil and the provided images.
I have a board that's connected via usb to the computer and I am trying to use the connectivity firmware...
In the nRF5340 user manual section 7.14.3, there is a note regarding assigning the same pin on more than one GPIOTE channel can result in unpredictable behavior. We have implemented...
Hello Jared,
the previous ticket find under the following link is locked. So I decided to open a new one.
https://devzone.nordicsemi.com/f/nordic-q-a/80312/uart-break...
Hi Nordic,
A important customer employ nRF5340 in their product, they are chosing the 32M crystal osciallor now.
Form the SPEC of 5340, if we want to communicate with...
I posted this theme, but the post is locked before fixed. I don't know the reason so repost. I'm sorry about this case.
-------------------------
Question:
I consider...
Hi,
I have a custom board with nrf52840 chipset that controls a GSM modem over UART, and this setup works just fine (zephyr project).
Now, I'm trying to replicate this...
Hi everybody,
I get this error trying to set coded_phy advertising on nrf52840 dongle. This is the code that i try.
The error that i get is:
That means I/O error...
I flash v1.7.0 at_client and mfw-v1.3.0 into nrf9160-DK board, LTE works normally and the board can get the ip. ( https://files.slack.com/files-pri/T0SBEQ7AR-F02J4REC8RX/nordic...
I'm trying to implement communication protocol that involves clock and bidirectional I/O line. Clock signal is coming from an external device and expected to be in 1-5MHz...
Hi,
Could you please help to fill which nRF9160 SIP revision fit for SDK?
nRF9160 modem firmware version
nRF Connect SDK
nRF9160-DK, SIP revision (BA, B0,...
Hello,
I have a question about the best way of implementation.
The data will consists out of a struct with multiple pressure and temperature measurements coming from another...
Hi everyone,
I have this question to ask. So I am trying do make an end device that run on low power. I can see that there is an example about the sleepy end device in the...
