Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
How do I get following combination to work:
Nrf connect 3.6.1 power profiler with PCA10040 v1.2.1 + PCA63511 v1.1.0 with external power supply and external DUT
The same...
My error messages in Segger studio are messed up (shown below). Everything else is fine. Can I change the font or something?
[m[K'[01m[Kdev[m[K' undeclared (first use in...
Hello, I have a 52832 using SDK16.0.0, that acts as an advertising peripheral (anyone can connect to it), and as a central, connected with 1-1 bond to a peripheral (a 52811...
Hi, using the Nordic power profiler 2 (PP2) kit to measure the current draw of my nRF52833 DK. I have followed the instructions to setup/prepare/wire the PP2 to my DK and...
In the task, when I do a TWI read via nrf_drv_twi_rx(), in the second iteration of the thread, the driver function returns NRF_ERROR_BUSY.
Is it that the driver takes longer...
I've built a custom board using nRF52832 which uses SDK 16.0.0 and softdevice version s113. A part of application is audio streaming/ decibel calculation and transmission...
Hall Mr. Nordic,
I'm sending a 16bit payload with 51822.
The receiver 24L01 is receiving all perfectly. The receiver 52840 is loosing the first two bytes ...
nRF51822...
Hi,
I'm using nRF52840 as my server and the android mobile is my client. At the client end, I'm using the nRF Connect app. It seems like the 50 bytes of data is taking around...
Hello,
I have an nRF9160 DK board (I believe the version is PCA10090 1.0.0) and would like to use the external flash that comes with this board.
Upon inspection, this...
Hi,
I'm seeking help on debugging the network core with Visual Studio Code. My project is not based on a standard SDK and hence I think VS code will be easier to setup than...
hello!
I have an issue, I need to read data from a Module, then I send that data using USBD..
when I put that code in for(;;) before while(true) the port is activated...
The nRF52840 DK has a 64 mbit external flash on board. The MX25R6435F.
It's performance is too low, in terms of erase speeds - It takes several minutes to erase the entire...
I'm trying to upload hex files to my NRF52832 with nrfjprog in command line and got the following error:
My log file:
I've been searching and searching, but could...
Hello,
I am new to the NRF52 SoC and BLE development. I've been using the ble_app_template and following along this tutorial to learn more about BLE development. I'm having...
