Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi Nordic Team,
when discovery custom 128bits uuid service, I have high probability get BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND, but sometimes I get BLE_GATT_STATUS_SUCCESS...
Hello,
I am upgrading my project from SDK 15.0 to SDK 17.0 and I get this message.
Please see my project's comfiguration file:
debug_additional_load_file="../SDK_17...
Hi, all
I'm trying to i2c(twi) in low power..
In this case, I want to generate an interrupt through the i2c read function " read_touch_data " (under code).
Where...
Hello team,
We have a sensor design based on nRF52840 and currently we have configured it in the normal voltage mode DC/DC REG1 enabled. It is a battery operated design...
hi,
I am using nrf5340 dk board and nrf connect sdk. i want to encrypt the data and decrypt the data in application core. I have seen cryptcell 312 for cryptohraphic algorithms...
Hi,
I am currently working with the nrf52840, ble_app_uart example under the ble_peripheral folder. Using the tutorial below:
https://devzone.nordicsemi.com/nordic/short...
Hi,
I want to receive data on BLE and send it through USB to PC, I am using SDK17 and nRF52840 dongle. I send data from the transmitter with nRF52832 through ESB configuration...
Hi,
I'm currently developing the code of a RGB led lamp. The thing is, when I change the color while sniffing with Wireshark, I see only 1 payload (the way it should be...
How to easily migrate SDK to SDK, (Lower to Higher) or (Higher to Lower).
I mean from SDK 14 to SDK 17 or vice versa.
Please answer this as soon as possible
Hi,
I am pretty new to telecommunications and AT-commands in particular. What I want to do is:
-Scan all nearby base stations (BS), and read all available information...
Hi.
I'm developing a sensor driver for the Spec Sensors DGS-O3 968-042 UART gas sensor for the nRF9160 (Thingy:91 to be precise)
The general gist of it is that I need...
If we want to make certain that a particular message goes first on a connection interval. Is there a way to check that there is none already internally queued?
Is this...
hi i am using nrf52832 sdk v16, i need to print a data using uart example got a issue it's not getting app_uart_put & get function not working but printf() function data are...
We are fast-tracking into development using the nRF5 SDK samples and nRF52840 dongles, however have discovered so far that only the Blink sample supports the said dongle....
I want to Connect my nRF52840 Dongle with the nRF connect Mobile Application to send and receive a string from the mobile application to dongle via UART connection.
Please...
