I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi. I'm working on a code that performs an action and immediately goes into System OFF mode. Before that, it configures GRTC as a wake-up source with a 5 secs timeout. I've...
Hello, I designed a new custom PCB with nRF52832 and I would like to ask you for verification.
I have the MCU and some components regarding Battery Management.
The idea...
Hello,
in my application I use SPI communication to control my display. For that I have configured the pins for spi4 in the dts and all works fine.
Now I would like...
Question:
What's the maximum NRF_SDH_BLE_GATT_MAX_MTU_SIZE supported by S113 v7.2.0 on nRF52833?
Current setup:
Chip: nRF52833
SoftDevice: S113 v7.2.0
...
I am following the nRF Connect SDK Academy, Lesson 1, Exercise 2 on a Windows 11 system. I got to step 4.12, "Click the build configuration button." After running for some...
Hello,
The MPLAB Snap debugger says that it supports "Cortex SWD". Can I use this to program an NRF54L15? Ideally I'd build the program in nordic vs code and then take...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). I am using a custom board. Below is the configuration I set in .overlay file
And below...
We would like to reset or factory reset or initial flashing of nrf52840dk? We tried pressing RESET button during power cycle, but did not worked. Let us know your thoughts...
Hi,
I'm designing a battery-powered device using the nPM1304 PMIC and nRF54L15. I want to implement a sleep/wake function using a single button.
Desired behavior:
...
This has been resolved, but resolving this issue took quite a bit effort: I was wondering why my NFC was not working on my custom board. First I thought it would be an antenna...
Hi Nordic Support,
I’m designing a product with the nPM2100 using NiMH batteries .
I know the fuel gauge feature is designed for primary cells and lacks hardware coulomb...
Hi,
The Bluetooth Channel Sounding specification empowers every compatible device (like the new nRF54L series devices) to be a mini radar actually. The Bluetooth Channel...
Hi,
Our team is considering the use of SiTime MEMS oscillators, namely a SiTime SiT1615B, to help in harsh shock and vibration conditions our product will be used in....
Hi, I am using the nRF52840 DK with SDK 17.0.2.
I am working on a project using the ESB protocol. In my design, an ACK packet is transmitted to the receiver every 5 seconds...
