Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I've been trying to modify the v2.4.0 Serial LTE Modem application sample for my nRF-9160 custom board, in order for it to communicate with our external MCU through...
Hello,
I'm currently running into issues when using the Logging Interface with USB CDC ACM. I tried to combine the cdc_acm sample and the console sample into one application...
Hello,
I measured the DC resistance between the RF output pin and ground pin and got around ~3-4 Ohm with digital voltage meter. This seems low. Am I missing something?...
Hi,
I have two nRF52833 DKs and both of them has connected to nRF21540 EK. I set the transmitter sending out 244 bytes data without stopping and measure it's current. The...
Hi there,
I want to debugging my beacon project card which designed with NRF52832 MCU
I have NRF54L15 PDK Development Kit and it has debugger on the kit.
How can I debug...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I'm studying the nRF Connect SDK Fundamentals course and working with the NRF54L15 PDK. In Lesson 1, I'm trying to turn on LED0. I can build and flash, but the LED won’t turn...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol.
...
The nRF Kconfig extension ( https://marketplace.visualstudio.com/items?itemName=nordic-semiconductor.nrf-kconfig ) does not recognise some of the Zephyr kconfig extensions...
We are currently developing an ECG sensor patch that will operate over a cellular network, and we are considering using the nRF9151 for its LTE-M/NB-IoT capabilities. Since...
I'm interested in determining the current coverage enhancement behavior of a device, and I'm noticing a discrepancy between the AT+CEINFO and AT%CONEVAL results. Specifically...
as my last post issue nrf desktop in ncs SDK cant work when onnect to cmac os - Nordic Q&A - Nordic DevZone - Nordic DevZone .the ncs desktop cant work in mac os in nrf52840...
We are currently mass producing nrf52833. However, there is a problem with BLE communication. The defective product does not appear in the BLE search list at all. The failure...
Hi,
I'm working with UART with DMA(UARTE) on nRF52840. UART does not have HW flow control, just RX-TX.
I'm confused with DMA part. Is DMA circular or I have to reset it...
