Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hello
I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to -3dBm and test again. I use the...
Hi,
I develop a python software that flash 2 nRF chip (nRF52840 & nRF9160) with pynrfjprog (version 10.15.2). All the dll are wrapped into the generated exe and the jlink_arm_nrf_worker...
Environment
Platform: Windows 7
IDE: SEGGER Embedded Studio for ARM V5.42a (64bit)
SDK: clean nRF5_SDK_17.1.0
Project: usbd_ble_uart_c_v4 and modify with usbd function...
Hi All,
I have implemented sleep mode in the firmware. I am using NRF52833 in my project. When the device is in idle state it goes in sleep mode. Now I wanted to wakeup...
Hello,
SDK17.2, nRF52840, Keil5, SIP cannect to a OLED,
now, i want to OLED show text "DFUing" in the bootloader,
when no app, bootloader can show text in OLED, but...
Hi Sir/Miss,
I'm using nrf52832, softdevice s132 and SDK 17.0.2.
In specification, I saw nrf52832 has a ultra low power mode.
It's in system on with full retention RAM...
Hello Devs,
My device is passing through a certification process and shows up a question, which is the maximum altitude for nrf52810 for functionality. If exist any maximum...
hi, i am using nrf5340 custom board, i m trying to recieve data through uart in nrf5340 custom board from some other board.
i have defined separate pin numbers for rx and...
Hi,
I am starting to play with the nRF9160 as a modem with an external MCU and I can see that the CMUX multiplexer (GSM 07.10) is not supported by the internal modem....
I set static passkey to "123456" and enter "123456" in nRF Connect passkey request dialog. But sd_ble_gap_sec_params_reply() return 0x8 error code.
static void ble_evt_handler...
Hey! I am starting my studies in the BLE protocol and I would like to send the ZE03 sensor data through the Nordic UART Service (NUS).
The sensor continuously sends 9 bytes...
I have to interface the spi flash with NRF52 to store the data and retrieve the data back. Read, Write and Erase the data collected from sensors. The problem is the device...
Dear Nordic，
We have developed a product based on nRF52832 with DCDC regulator and no external crystal. The radio transmit power is 4dBm and the advertising interval time...
I've been slowly adding NVS functionality to my code. Has been working fine, up until today when I attempted to write a struct I have for storing historical data to flash...
Hello,
I'm Electronics designer, our Team faced some issue regarding BLE Mesh connectivity,
Q1. We have observed that It's taking so much of time(>3 min & upto 14 minutes...
