why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
hello Nordic
i am working with nrf52840 with ncs (on the process of moving to 1.8 currently 'v2.6.99-ncs1-1' )
i have several sensor drivers on my board and flash driver...
hello,
i am using nrf52832 with lis3dh accelarometer and max30205 temperature sensor in our customised board with sdk 15.2 i have included the dfu ota in my firmware my...
hello nordic team I ran the ble_app_uart example in sdk 15.3.0 on nrf52832. When i add printf("\r\n%d\r\n",15); to the code as follows, the program prints 15 to the serial...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a process to set the characteristic and send an indication using sd_ble_gatts_hvx...
Thank you very much for your help. I am currently working on implementing a PWM control function using the nrf52840. I would like to ask you about a build error that occurred...
I need to know in which case the SIW_DET pin is used. Does it depend on the version of the nRF9160 ? Then which versions ?
And is this detection function better in software...
Hello, guys!
I am using nRF51822 SoC with Zephyr. There is a need to configure multiple GPIOs as inputs, with the possibility to fire an interrupt on rising/falling/both...
Hi There,
I am working on a project based on nrf51822. I need to establish pairing the device with smart phone by clicking a button as confirmation on the nrf51822.
...
Hello,
I already fully understand how nRF5340: Network core bootloader working.
As I wondered in the title, I want to move the application firmware data of network core...
The project uses nRF5340. A signal is connected to P0.27/AIN6, and during "normal" mode the pin is used as an ADC.
Before going into sleep mode we would need this pin to...
Hello,
I am working on a project which is based on nrf52840 and Zephyr.
Current prototype uses Adafruit nrf52840 sense board with spi based display attached.
I am new...
Hi,
I experience a very strange issue with UART.
When I try to send data via /dev/ttyACM0 device it looks like the characters sent are buffered and sent only upon the...
Hi! I am in the process of trying to install the Asset Tracker on my Thingy91. I have got it to work with nrfCloud and I am now trying to configure it to use the AWS backend...
I am using the nRF52 SDK : nRF5_SDK_17.0.2_d674dde
- When data are all ASCII-Hex (0x30) the code working fine
- Now I try to optimize code by changing to binary data....
I have been using the nRF52-DK for while and it been good.
But when I accidental hold the "BOOT/RESET" button, the board now stop working. only LEDs is blinking (per sec...
