Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I have been evaluating the nrf9160 DK board. And my application is using mbedtls (vanilla) and TFM (Used https_client as a starter project). The problem is that with...
Hi,
I'm new to nRF/Zephyr development and trying to integrate the OV7670 camera with the nRF52840 board. Since there was no driver for this particular camera I ported the...
I'm having a problem with what should be a very simple exercise. I'm trying to compile the Zephyr sample subsys/cpp/cpp_synchronization after adding #include <string> to the...
Hello,
I am trying to read data from LS2DE12 accelerometer MEMS chip via I2C bus and I am seeing only zeros for all 3 axes.
I can write to the various registers successfully...
Hello, I ran the nrfconnect (ver 3.7.1) in Power Profiler (ver 3.1.3) in BLE advertising.
When I run the source mode on 3000V I get normal peaks (20mA), however when I run...
Hi,
I'm interested to use AGPS in my project. Looking into AGPS example (link below) , I want to prevent using low power mode since as far as I know using this command you...
Power Profiler software returns an error after I updated it to v3.2.0 with nRfConnect v3.8.0.
Error message: Error while probing devices: EnumerateWorker json error
Resulting...
Hi,
I am working with nRF52833 DK with nRF Connect SDK. All was going great until I had to add a GNU GSL library. I need it because I need matrix multiplications with complex...
Hi,
We are working on a custom bootloader/DFU and is going to use USB CDC to perform DFU and some data transfers for version information. We use the USB CDC library both...
Hello,
SD: 122
part nrf52833
I need to do the following:
a. scan for advertisements containing a particular MAC address without connecting. This works.
b. the...
Are there any convenient ways to debug BLE connectivity issues? I have the service up and running but the connection on nRFConnect App doesn't quite go through: it remains...
Hello,
I work with the nRF5340 and want to use I2C0 (1-3 is reserved for other sensors in my project ). I already use I2C2 for a sensor and this works fine.
To use the...
Sorry I'have a question about the certification process of a BLE in a custom board.
I see that with zephyr that I can define a custom board derived fron nrf52840dk. If for...
I powered the DK up and the LED's would light corresponding to the button that was pushed.
The D drive would come up, so I drug the heart rate demo (hex file) to the drive...
I was trying to follow the video to create a project with VS Code. After I click the Create Application buttion, there is nothing happens. It only create a Folder with APP...
