Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi,
I want nRF52 Continuous Unmodulated TX carrier.
Is it possible by TASK_TXEN and TASK_START or radio_tx_carrier command of radio test example, after TX configuration...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi, team I am trying to build a system with one master and multiple slaves using the mesh SDK. ( This is similar to the light_switch example. ) At this, I want to give each...
After the update to nRF Connect v3.0.0 none of the Nordic devices is detected anymore by that tool.
I even un-installed and reinstalled nRF Connect v3.0.0 (as recommended...
Went through the pin_change_int example and of course it works fine.
Migrated that to custom board and it also worked fine with main loop.
So I then tried to use that...
Have an application that configures a wifi SOC using spim before enabling BLE scanner.
When it is running there are 4 timer events running and the main loop check status...
Hello,
Zephyr 1.14.0 includes the nrfx code to use GPIOTE and PPI and my code compiles but I get
undefined reference errors to the nrfx_gpiote_ and nrfx_ppi_ functions...
Few issues I'm facing -
1. I have gone through the related blogs, tutorial, documentation for DFU. nRFConnect cannot connect to the Fanstel BM832 chip. It gives me an error...
hi
I connect AT24C02 EEPROM with nrf52dk.
I already test EEPROM with arduino and it work fine.
Now i want to communicate with NRF52DK kit,so which example I would prefer...
Hi Nordic.
I have an issue that I'm really stuck on. I am trying to send data from a radar sensor via your nRF52 DK BLE board. I've managed to make a working connection...
Hello,
we would like to use a nRF52DK for a simple bluetooth production testing as mentioned in AN34. If we are using an external 50R antenna on J1 do we need to cut the...
I am using nRF52832 SDK 15.2.
I would like to avoid using the 32.768kHz oscillator to save space and cost.
I am using BLE and sleep mode ON.
I defined in sdk_config...
If I build/flash from the command line with "west build -b nrf9160_pca10090ns" and "west flash -d build" it loads a fully combined image with mcuboot and (spm+application...
I am trying to write a program in C to have my central device(nRF52840 dongle) read the RSSI from a peripheral. I have never written C code before and was told to use:
TASKS_RSSISTART...
