Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to do i2c communication between Renesas...
Good morning, I have built and flashed the l2-e1 exercise on both the nRF5340DK and the nRF54L15DK. When the nRF54L15DK boots, the following output is displayed in the terminal...
Hi,
I’m working on nRF54LM20A and trying to configure the internal capacitors for the 32.768 kHz crystal (LFXO) using the factory trim values in FICR.
According to the...
Hello, read through the documentation about the SAADC and found the TRIM.LINCALCOEFF[n] register. ADC-linearity is important in the project I'm involved in... Seems that the...
Using nrf connect SDK 2.5.0
The nrf device is an L2CAP CoC server. I am using an RPi 4 to test with. The application is for transferring data through UART to another chip...
Greetings!
We have been using an nRF52840 Development Kit for a while now and have been performing FW updates OTA (between the same 3 FW images, cycling and updating between...
I am still on the learning curve of nRF Cloud (and the nRF9151 in general) and am trying to add A-GPS to a project.
Using nRF Connect SDK and Toolchain 3.1.1, I cannot add...
I am using the nRF Connect for Visual Studio Code Add-In running with the nRF Connect 2.5.0 toolchain and was trying to implement the application versioning on a nRF5340 DK...
Hi,
I am working on a project which uses nRF5 sdk v17.1.0 & mbedtls v 2.2.8.2. Now i ma planning to make some changes in application code and re release it. My question...
There appear to be mistakes in haptics_handler.c it appears to be using outdated functions / includes in NCS 3.2.1:
The corrections that work for me:
Changes made: ...
I must have the PPK2 data logger running for too long .because now it won't start. I see the currently available space is 0.0 MB, so maybe that's the problem.. I tried to...
Hello there, I trained my own model using LSTM and a window size of 25 for temporal encoding, and then did the TensorFlow conversion for deployment on the edgeimpulse platform...
I would like to get my Thingy:91 X to receive Location via GNSS only (no cellular, no A-GPS, no P-GPS, no AWS). Thus, I adapted the code from the "Asset Tracker Template"...
Hi,
I am working on the nRF9151 DK (nrf9151dk_nrf9151ns) and need to use an additional UART for communication with an external ESP32.
Currently:
UART0 is used for...
