I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I'm restarting development using an older nRF Thingy:91 .
When I first started up "nRF Connect for Desktop" and the "Cellular Monitor" a few weeks ago, I managed to get...
Hi,
starting from ncs 3.2.0 (also in 3.2.1) when i attached the debugger (jlink ultra+, under VS code with nrf connect extension) to my nrf52833 board, i am getting the...
Hello,
We're working implementing a custom board using he nRF54L15 and looking to use the NFC functionality. We have run into an issue that occurs when we try to read the...
Hi, I'm trying to determine whether or not an nRF54L15-DK running Zephyr supports the following relatively recent Bluetooth features and if so, how to enable and use them...
Hi, I'm using v4.0.4 of the standalone Bluetooth Low Energy desktop application to obtain and display GATT details of a connected device. I enable indications on the Service...
One of our employees is following the Cellular Fundamentals courses and they got stuck on getting modem traces out of the Thingy:91X.
In lesson 7 exercise 1, the course...
I have been trying to understand Child Supervision. Part of the documentation that I have read is:
https://openthread.io/guides/build/features/child-supervision
At the...
Hello!
I'm working on a project that was primarily developed with NCS v2.9.0. The application (using an nRF5340) utilizes BLE mesh and is configured to use TinyCrypt for...
Hello,
I am using nRF52833 with nrf connect sdk for vs code (SDK and Toolchain version : 2.9.1).
Hello Nordic Team,
I am using OTA DFU with MCUboot on the nRF Connect...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
I am trying to flash and use the debugger on a nrf52840 DK to flash a Thingy53, using the ribbon connector as outlined in this video . I tried to follow the steps in this...
nRF9160, SICA B1A, mfw 1.3.7, NCS 3.1.0
I currently try to test the situation, when the battery gets drained "too much" and the voltage drops below 3.0V (e.g. 2.9V) on VDD1...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
My project is running on an nRF52832 with the soft device enabled. At the start of my project I have the following
When I reset the system our normal way (calling nrf_pwr_mgmt_shutdown...
