Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode,and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Your old documentation website ttps://infocenter.nordicsemi.com/ carries a banner saying it will be shut down on 18 June 2024. Please don't do this! I can't find equivalent...
I'm running NCSv2.6.0 on some custom hardware, with an nRF52832 IC fitted. I'm trying to trigger an ADC measurement every ~ 300usec using a Counter, so need to set the Counter...
Hello community,
I am working on a custom nrf5340 board design, that uses the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module...
Hi,
I've attached the steps performed to install the mosquitto bridge and getting errors on yarn deploy
Also see attached steps, I believe I have done everything correct...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
You may ask what poolside means. It means at my community pool, where I don't have Internet access via Wi-Fi for my laptop.
I wish to run some AT commands like AT%NCELLMEAS...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
I'm confused about the use of these two functions. I want my app to sleep immediately upon start and then wake up and do a BLE advertise when I press a button.
I...
Hello everyone,
I've been spending a lot of time to fix the issue not being able to enter DFU mode with the following error. I've changed so many versions of GCC, but it...
Dear Nordic devzone community,
I have designed a custom board using nRF9160 and I am able to send and read out certain AT commands which confirms to me that most of the...
I'm transitioning from SES to Visual Studio Code.
In SES, I can define multiple builds and then define preprocessor options (eg. -DOPTION1) for each build definition
I...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...