I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hi Dear
Is the WLCSP package of nRF54L15-CAAA a glass package?
Is it similar to the WLCSP package of 52832-CIAA?
The above refers to the molding material.
If possible...
Hi Nordic
What is the best way to protect against downgrading the APP FW via DFU.
I seems that im able to downgrade even 2 config below are set.
I tested it on SDK...
Hi,
I have two PPK2 units, and under the exact same test environment and PPK2 settings, simply swapping the PPK2 results in completely different measurement results. Which...
Hi all,
I'm trying to combine two NFC messages, I know that I can combine multiple records into one message. But the problem is that OOB_LE message will already contain...
I'm fairly new to Zephyr and initially I'm hoping someone can point me to an example where SMP over UART can be used to update a firmware image slot. Google seems to have...
Dear All,
We need to develop a custom low-level driver for NFC communication using the Hardware Abstraction Layer (HAL) library exclusively . We are currently unable to...
Was able to build after I installed these two packages
/usr/local/opt/python/libexec/bin/python -m pip install --break-system-packages PyYAML brew install pykwalify 2>&1...
I only learned today that the REGOUT0 voltage is changeable, which could be perfect for us, because our power needs changed dramatically.
Our circuit was originally designed...
I ordered a Thingy 91x and am tyring to configure it according to Introducing the Thingy:91 X – The Ultimate Cellular IoT Prototyping Platform on YouTube but I am getting...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello, I'm a beginner and trying to do my project with nRF9151DK. As said this project uses the nRF9151DK that requires high-throughput USB-UART data streaming on two boards...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
Hello, I would like to evaluate the Thingy 91:X, but I can't install nRF Connect SDK on any machine (Windows / openSUSE) due to various problems. I will try to break down...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
My design is in alpha test and we just discovered that apparently SPIM allows only one module to be enabled at a time. When a second module (SPIM3, SPIM2) is enabled, the...
