Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
1.I am testing the NRF5340 Audio and fully following the
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/nrf5340_audio/README.html#fota-build...
Hi,
I tried to use the sensors on the Thingy:53.
However, it looks like the BMI270 on the Thingy:53 is not supported by the nRF Connect SDK because the SDK only supports...
Hello everyone:
I'm following the tutorial in JWT authentication on nRF Cloud | nRF Cloud Docs .
And I want to test the REST APIs by using curl command.
I have created...
Hi,
I think this is a regression or related to this issue:
Attached is a very simple example with the [email protected] - if you build it with `CONFIG_DEBUG=n`, it...
Hi all! I am working in a BLE scanner but I have enabled the filter by MAC ADDRESS. I can filter beacons that are produced based in NRF52 and NRF51. But when i try set a MAC...
Hello,
I am running into difficulties getting the sleep current below 2.356mA. I have a custom board but I went ahead and tested it sleep current capabilities by programming...
Hello,
My application (nRF52832, SDK17.1) uses the fsotrage library for low-level sequential data storage and retrieval.
At the moment I'm using nrf_fstorage_sd as an...
Hi,
I am using nrf sdk for mesh v5.0.0 and we are building our application on top of sensor_server example. I am provisioning the nrf52832(which is acting as sensor server...
Hi Team Nordic,
For setting up a thread network using nRF5340 DK's, I wanted to build and flash Thread: CLI sample from nrf repository. I use nRF Connect for VS Code with...
I’m using the nRF52840DK to communicate with a module over uart. My problem is that the module has a baud rate of 921600 and as far as my understanding the nRF52840 is using...
Hi,
in my current project I need to have a wall clock time, thus I am using the date_time library. While trying to understand it I came across a few issues/questions.
...
Hello,
First let me say I'm new to Nordic tools and SDK. I have been lurking on this forum for a while and it has helped solve a lot of my issues in the past. I couldn't...
Hello
I tried to follow the instructions to install the nRF SDK Connect and I found the following issues:
There are 2 sets of instructions :
option 1 :
https://nrfconnect...
Hi! We would like to build two different sw variants from same source code and mostly the same config options, probably only needing a single "define"-difference in code....
Hi,
We have a question regarding firmware over the air update, can we update the firmware of the devices connected in Mesh network or we need to connect single device...
