dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
We have developed a customized board for use in a gateway. We would like to have a working bootloader on that board but it looks like it is almost impossible to make...
I'm working with the OpenThread CoAP protocol in the nRF Connect SDK 2.0.0. I started with the samples:
\ncs\v2.0.0\nrf\samples\openthread\coap_client
\ncs\v2.0.0\nrf...
Hello,
I have added service data to my advertising_init function, however it does display when looking at the nRF Connect app. I'm not sure why it doesn't show as it's similar...
1. The code uses a value 0xFF55AA5A to identify the adv packet as the one that supports distance measurement. Is this value checked by lower layers?
If not - why not just...
I can successfully perform a DFU of my BLE device via the Nordic "nRF Connect" App using a nRF52 DK. I'm trying to do the same via nrfutil CLI, now running into an issue:...
Hello,
I'm working with the nRF Connect NVS module on the nRF9160. Every time there is a read/write to NVS the messages:
I: 3 Sectors of 4096 bytes I: alloc wra: 0, 668...
Hello With Zbus being added to Zephyr, are there plans to carry on support for the Application Event Manager and the CAF or switch to using the Zbus system in future releases...
Hello,
I am new to the microcontroller development club and have recently obtained a nRF52 DK kit. I am using the new nRF Connect SDK and have the Arducam OV5642 camera...
Hi there,
We have developed a family of BLE products based on the NRF52832 using it's maximum TX power 4dBm.
We have a strong push for increasing the communication range...
I have a simple application running on our custom board based on nRF52840. Our board does not have any uart pins connected so we use RTT exclusively for console I/O. I attempted...
Hi! I am trying to use the Power Profiler app on my Windows computer, I have used it on another Windows computer, and it worked fine. Now, when I try to open the PP app, it...
I’m working on a project trying to characterize the range (given a certain transmitter and environment) on the BLE 1 mbps PHY. I’m using a few nRF52840 dongles to do this...
Hi,
I am evaluating nRF5340 audio dk with CS47L63 DSP. My goal is to find out the MCU processing consumption for LC3 codec what is MCU processing power left for the application...
Hi,
I am writing a program that sends numbers counting up sequentially from my dev board to my phone on 500ms intervals. I used the ble_app_uart example as my base. I am...
Hi all,
I trying to use test-harness v2.6 raspi and nRF52840dk to test commissioning. The result is always failure, and the error is timeout
The firmware DK flash is build...
