Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello Support Team,
Our product design uses a custom BLE service and solution with the nRF52832 on our own board. Also, this BLE peripheral device does not use any BLE pairing...
This example automatically create the thread network. Once the button is pressed every 3 second udp is sent.
Issue is I am not receiving the packet on 2nd device. I am not...
Hello, we came across a recurring issue:
There are no executable permission for Linux + macOS for the packed binary:
jlinkarm_nrf_worker_linux
jlinkarm_nrf_worker_osx...
Hi,
I have written the BLE UART code With custom characteristics. I have flashed the code to DK and tested it. but that was not working correctly. Then I flashed the sample...
Let me start by saying we have not ruled out other possible sources of errors at this point. However, right now all the evidence is pointing to an issue with the nRF52840...
I attended the Introduction to the nRF21540 RF FEM for range extension webinar and bought a few nRF21540-DB kits
The first thing I want to do is compare the range increase...
Hi,
We have our own MQTT broker setup with TLS running on a AWS EC2 cloud service. I am building my code based on the MQTT_SIMPLE example. I have only a CA certificate in...
In my project I use nRF52832 embedded in MuRata module. I have a BLE service with capabilities very similar to NUS service.
I've managed to add support for LESC + SEC_MITM...
I am attempting to upgrade from nRF Connect SDK version 1.7 to version 1.9.1
My application is using the nrf52840 on a custom board.
I'm using Zephyr and created a board...
Hallo,
I am starting to develop an application using nrf5340 SoC. I have got two Audio DK and would like to begin my development using nRF Connect SDK.
However, I was...
I was trying to schedule a work item when a struct k_poll_signal is raised by an interrupt, but was unable to get the work to happen. I could tell that the k_work_poll_submit...
Hi, I'm new to this and I was just wondering, since I'm still learning and successfully coded my first app, I'm asking how can you flash / burn / build & run SMD component...
yes, i meet a problem.i notice that isp have done a AOA demo based on Nordic board.
but i use it to get the angle.i find i can't use it.what is this problem?
I am running a nrf52dk_nrf52832 build with SDK v1.9.1. A week ago I was building my project and everything was working fine. Then, my program stopped being flashed - I could...
