dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I'm a newbie of microwave board design, after many research I finished our 2.4G USB Receiver board which use the nRF52840-QIAA. But I still want some advice of the RF...
Hello,
My setup is UDP sample and PPK2 for power measurements. I am trying to figure out the best settings that are available with eDRX set to <= 20.48s, and preferably...
Hello,
I am trying to get the data out of an out of the box zigbee sensor (PIR motion sensor) with the CLI example provided.
I flash an NRF52 with the CLI example, and...
We are working with tuning of the GPS:
Basically the tuning is fine but we are mostly bandwidth limited.
I wanted to ask how much is the acceptable bandwidth for a GPS...
Hi Team,
I am working on air mouse development using NRF 52832.
nrf standard package support ICM 20608 with AIR_Motion Library , but its not available now in https://www...
Hi,
I have noticed that when a peripheral (using NUS) is disconnected from a central it takes 2-3 seconds for the peripheral's BLE_GAP_EVT_DISCONNECTED to trigger.
Shouldn...
Hi,
I encountered that the PWM couldn't be closed completely, it still has about 100uA after PWM is uninitialized.
For troubleshooting purposes, I have posted my code...
I am working with SPIS on nRF5340. Since my RX and TX buffers will not change, is it possible to call nrfx_spis_buffers_set only once, during initialization? I tried to do...
I am creating the Battery characteristic in a Battery service but I run out of memory (0x04 error) when generating the characteristic. However, that makes no sense. I have...
We’re using Nordic Semiconductor nRF52840 and we may have some problem with RTC when we simulate a brownout. In our application we have both coin cell battery and external...
when I am trying to setup linux with this link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.1/nrf/gs_installing.html#install-the-toolchain
On typing this command...
Hello!
I would like to know the gain of the integrated PCB antenna on the nRF52832 chip. Is there a documentation paper on the antenna itself? I couldnt find any info...
Hi!
I am evaluating DFU over Mesh by following the configuration guide here Configuring and performing DFU over Mesh . I am trying to prepare a package with the application...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I have a question about setting the UUID. My program has one advertised UUID...
