I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi,
I am trying to transfer a dataset of over 100k, via a custom service from a peripheral device.
There are many posts in this forum that describe ways to do this but...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. The Client sends unacknowledged messages to the Server ( APP_UNACK_MSG_REPEAT_COUNT...
Hi,
We are facing some issues with the DLE update.
The given table shows that the softdevice set data length and time.
Event Length (ms)
ATT MTU (bytes)
Data...
I'm trying to build "application_update" sample. I created a new application from sample. added build configuration for nrf9160dk_nrf9160_ns board and changed to variables...
Hello,
I have the Feeling with nrf connect programmer you can't select the Network core.
I use Programmer Version 2.2.0 and have our own hardware but also the nrf5340...
Hi Dev team,
I have been working with code development using Thingy91 and NRF Connect for Desktop. I use GitLab to maintain and manage my codebase.
I wanted to use GitLab...
I have nrf52840 pcb without xTAL.
In this ticket ticket I have discused about start Zephyr project without XTAL onboard.
But now I faced with other issue to start mcuboot...
Hi everyone,
I'm using nrf52840 as a connectable advertiser. Used ble_app_blinky example with some modifications. And I reduced the advertising interval to 2 seconds....
Hi, I'm using the example "libuartes" and developing 2 UARTE. But I dont know how to recoginize what port are communicating with external device because I only have 1 uart_event_handle...
Hi, Im trying to use nrfjprog from inside a docker container (ubuntu). I have started the container with --privileged and it seem to work but when i try to run the container...
Hello.
I use nRF52832 with SoftDevice and several TWI-connected IC's.
The power consumtion of nRF52832 is 14 uA after TWI initialization (low power mode and DC-DC regulator...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
Hello,
We are using nRF52840 chip for a power-sensitive application.
We use the UART which is connected to a LoRaWAN module.
Now when I enter the system ON mode after...
Hi,
I just started working with Zephyr and having some problems right out of the gate.
Board: Nordic nRF52840DK Example: i2c/spi_fujitsu_fram Branch: Main
When I'm using...
Can Nordic team be sure that SweynTooth test team has tested Nordic chips? If so, the claim in Nordic dev zone that Nordic chips are not listed indicating Nordic chips are...
