I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi, dear Nordic & all：
I found nrfx_saadc_uninit() did not work when use SAADC's differential mode with SDK17.0.2, nrf52832, the fellowing is saadc init and configuration...
Hi, there:
based on \\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132, I need add Just-Works bonding function. But this bonding request need launch...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_template_c but when i run the code i get the following below error are as follows...
Hello,
I am compiling my BLE project on nRF5340, with nRF Connect SDK v1.6.1. I got this error: undefined reference to bt_gatt_exchange_mtu.
My code works fine on SDK...
11:14:55.624
Received status with code 0 PKT_SEND_MAX_RETRIES_REACHED, message: 'No response from device. Tried to send packet 6 times.'
11:14:55.954
Server setup...
Hello,
I am looking at the Asset Tracker v2 example and was wondering if it is possible to use the A-GPS or P-GPS services offered through nRF Cloud if I am using AWS or...
Hello,
Both parts part#nRF9160-SICA-R and nRF9160-DK are available on Mouser website but t he customer would like to check what revision is.
Could you please help to...
Also please let us know if there are any antenna design specifications.
If we use other antenna for NFC is your certification valid or we need to re-certify our product...
Hi,
I've been experiencing some very slow erase times in the erasing / programming stage. Consistently around 10s. I am using SEGGER Embedded Studio, J-Link V7.22, and...
Hi all
According to the PS of the nRF52832, the INFO.VARIANT field in the FICR is ASCII encoded (e.g. 0x41414530 -> AAE0).
Are only capital letters ('A' - 'Z') and numbers...
Hi everyone,
My task is make Uart peripheal advertisments on coded phy, for that i CONFIG_BT_EXT_ADV=1 on autoconfig.h, and I add the function bt_ready of the project peripheral_hr_coded...
Hi
I want to design a GATT service as a connectable peripheral device. My board is NRF5340-DK.
The software which I am using is NCS(based on Zephyr).Which sample code...
I integrate dfu into light_switch example. Current consumption before flash bootloader is 200uA, but when i flash bootloader it increase 1.2mA. How do i disable bootloader...
