Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I just received my Thingy91x. I followed the onboarding and created a provisioning profile in NRF Cloud. The device did not connect and no logs appeared in Serial terminal...
Hello everyone,
I am trying to execute Nordic Bluetooth ESL tutorial with PAwR. Here, I am able to change the images and handling the state of an LED connected at the Tag...
Hi,
We are encountering an issue where the existing firmware does not run on the chip when powered by a coin cell, even though a 3.3V power supply is available from the...
When I compiled and flashed the Nordic Distance Toolbox example onto two nrf5430dk boards without changing any options, the following message appeared on one of the UART ports...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi, I am using a custom nrf52832 device. In that device , button is connected with reset pin P0.21. due to reset functionality I am not able get interrupt from button.
how...
Hi,
I am using nrf52840 to develop a product. I use NCS sdk v2.5.0.
I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
Hi,
i am using SDK 2.1.1 with nrf5340.
I would like to add the linker option --wrap.
What are the possibilities to add this option in Visual Studio Code ?
Could it...
Hi,
I am using nrf connect SDK 2.9.0 with nrf52840DK and MCUboot with own RSA .pem file (from older versions, so no ECDSA possible). How can I increase verbosity when building...
Hello,
My BLE peripheral code works fine with Android devices, but it is failing with iOS devices. I am encountering an error message: "Ignoring data for unknown channel...
I'm working through the tutorial here. https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial-communication-uart/topic/uart-driver/#uart_config...
I'm working with nRF52840, my function will read wav file from SD card and play it using Zephyr I2S driver. My source code about playing sound in below.
The strange is the...
Hi,
For a meter application with battery, I want MCU is sleeping but comparator still working to count a pulse input (freq <100khz)
Can Nordic IC can support this idea...
Good day. I'm working on a custom board that uses nRF5340 as the main MCU with a WIFI module, nRF7002. The nRF5340 and nRF7002 are wired based on the nRF7002DK. When I uploaded...
My project as above.
I'm developing my code in nrf52832,with nrf SDK v17.0.0.
I try to add some customized params by FDS so that I can get them after the next run.
The...
