Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hi,
I try to change the endianess of transmitted data from Little Endian to Big Endian.
So for example when I want to transmit a value uint32_t valueTx = 0xAABBCCDD
...
I have nrf 9160 DK board and sdk v 1.4.2 ( downloaded from nrfconnect toolchain manager ) .
For example blinky , which is the DTS file it takes and how do I modify it ?...
Hi,
Firmware v1.31
I have a question about using those call functions https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/lte_lc.html#c.lte_lc_deinit...
Hi,
I cannot compile the example/ble_peripheral/ble_app_uart project (others examples are compiled ok). I didin't make any changes. The errors are some files in the library...
Hi,
I am working on a personal project, and I have added my own functions in the ble_app_template project. I was trying to add the UART functionality in this project, based...
I'm using JLinkRTTViewer to view the outputs from the application and to enable the logging, I used the following configs in sdk_config.h:
set NRF_LOG_BACKEND_RTT_ENABLED...
Hello
SDK ver 17
DK nRF52 DK
DK is a peripheral connected to many centrals. Every time I connect to a phone I get the messages attached in the picture.. My question...
Hello, support team:)
Currently I am working on SPI communication with LSM6DSOXTR.
CLK, MOSI, SS is working as expected. But there is no MISO signal.
0) All SPI...
Hi,
Just would like to know is it possible to proceed auto pairing by restore the MAC address of host?
The current idea is using direct advertising to speed up the pairing...
Can a provisioner work as a client connect to a server
how do I set on the phone app(iPhone 10s)
in example/light_switch I did not do any change on the example
...
Hi,
I'm in the process of integrating nrf52840 module in HCI over UART to a linux host.
So far I have been able to build the hci_uart in from the samples and bring it...
Dear Members,
How can I share GPIO pin between SPI and I2C peripheral ?
I see SCK_PIN and MISO_PIN for SPI are the same with SCK and SDK on I2C
#define SER_APP_SPIM0_SCK_PIN...
