Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I have written a UART driver that is intended to receive data in a continuous stream. I know it basically works as it is able to communicate with an external device at 115...
Hi Nordic team,
I have a simple HID BLE device which send volume+/- multimedia keys to a Android device, it works
well if it is first time to pair with the Android device...
I'm developing a project that use BLE advertise and uart communication with other uC.
The uart part is based on libuarte example. To decrease the current consumption, I...
I am trying to do spp communication between central and peripheral with BLE.
First, the peripheral uses microchip RN4871.
The BLE setting is Service UUID: 49535343FE7D4AE58FA99FAFD205E455...
Hi,
I've been trying to run the zephyr's littlefs sample on Thingy:91 under the ncs 1.2.0 tag, but it seems that the flash_open_area function is having some trouble, and...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
When I am going to program a custom board for the first time, can I use example codes from the SDK or should I change anything important on the configuration?
On my custom...
I'm trying to create a simple service that would just provide some data which could get updated internally (for example, via SPI bus). Data may be of a different size, so...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
Hi,
I'm just getting started and tried to run the lwm2m_client sample from the v1.2.0 release of the nRF Connect SDK which I assume is the latest stable version? However...
hai ,
in my apllication i am using nrf52840 , i merged a code code of peripheral and central (app_blinky example)
i need to connect a peripheral to central (with esp32...
I'm working with the nRF52840 PDK and I'm wondering how to change the PHY (preferably to CODED) in a Mesh. Has that been implemented yet? Or when can we expect this feature...
When developing the dfu upgrade device, the code can be loaded to 100%, but the prompt "remote dfu invalid crc error" The compiled firmware can be upgraded with the old nRFtoolbox...
