Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
So, I am working on a handful of nRF24L01 to test some ideas out with radio devices and read thru many example source codes, libraries and datasheets and now I am going a...
Hello everyone
I want to develop a prototype by using nrf51822 but the problem is i did not find information concerning the packages please i request you to provide the...
Hi,
I know it possible for a nrf24l01+ configured as RX to receive communication from several nrf24l01+ configured as TX. (because RX has 6pipes.) I tested and that works...
Hi,
Loaded SDK8 S110 softdevice and application to nRF51822(pca10001), then the application works well. When I want to reload the sofedevice by nRFGo, I get the error message...
Working on a remote monitoring system.
Ethernet solution is on the table now.
But it needs to have extra chipset on board to do so.
I haven't had a chance to look into...
Is there any way i can get UTC time?
Is there any real time clock which keeps track of the time even if the chip is off?
I am using nrf51822 and require the UTC time...
Hey everyone,
I'm having problems with my app's ram usage as you can see from my previous questions.
I've tried this little piece of code:
void memcheck(void){
...
hello friends,
Im developing an application where im trying to connect a central and a peripheral but since the signal strength depends upon run time environment i am getting...
The App ~ BLE Stack is the device, Central is smartphone.
is correct?
I don't understand this sequence.
Do not adv_data_set and the adv_start before the scan?...
I'm attaching a function where I use the sd function :
void edit_speed_ID(uint8_t speed)
{
uint32_t value;//, err_code;
value=5 * speed;
while(sd_flash_write(address...
Unfortunately it seems my post devzone.nordicsemi.com/.../ has been lost.
This is a re-post.
I am trying to manipulate Flash data in CODE_SPACE one page at a time. Currently...
I'm using nRF51822 for ble.
For my application, I need to increase rf power.
( My application needs +10dBm)
In case of CC2540(TI ble chip), there is application note...
Hello,
I have 2 nRF51822 with S130. One is central, the other is device.
I want to exchange custom data between these 2 devices after connection. What is service best...
