As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
I am preparing my product for radio tests. There is a radio test example in the NRF5 SDK 15.3.0 that requires a UART interface that sends CLI commands to the chip. However...
Hi,
i am trying to read ADC value from my nrf9160 dev board, i can get the exact value upto 2.5v, if i go morethan 2.5v it decrease the ADC value. my values are
voltage...
I've used the nrf_inbuilt_key_write to store certificates/keys in the past, but I am still unable to do it using the "AT%CMNG" modem command.
I can list and delete items...
I attended Nordic Tech Tour - San Jose (Cupertino) on June 11. I did not receive a link for the presentations, as was communicated. Please advise how I can get the Tech Tour...
The BWG832F DK Bluetooth Gateway comes with a board that says that it can be used to program the Bluetooth module. The software recommended for this is the Nordic nRFgo Studio...
Hi everybody,
I'm using nRF52832 on a custom board mounting a BME680 sensor.
I'm running a third party library for the usage of the sensor (namely BSEC Library), and it...
Hello everyone, After having designed a pcb by taking the scheme proposed by the datasheet, I uploaded by the Black Magic Probe, the example code of the SDK "receiver Radio...
Hello,
I'm using the watchdog and i'm feeding it in my main loop :
I tried with
#define NRFX_WDT_CONFIG_BEHAVIOUR 1
and
#define NRFX_WDT_CONFIG_BEHAVIOUR 0 ...
Hello
I am using nrf52840 and am trying to determine the parameters of a voltage divider using the SAADC. Vin is the VDD voltage of the chip, R1 is 4640 ohms and R2 is 38600...
Hello Community,
I successfully build and run mqtt_simple it works fine.
I edit the code
//////////code///////////
void main(void) { u64_t start_time_mqtt; while(1...
Hello,
I am having an issue with the GPS on the nRF9160. I have been developing a custom program that will switch between NB-IoT and GPS when an interrupt pin is triggered...
Hi.
I am curious to know if it is possible to use the ANT-only Softdevice with the Zephyr RTOS. The goal is to create a BT BR/EDR + BLE 5.0 + ANT+ device all on the same...
Hi,
What is the maximum frequency that i can capture on GPIO port of nRF52840 ?
I'm planning to capture a frequency of 32MHz from a sensor on GPIO pin , can I do this...
Hi,every one!
As far as i konw, the original connection interval that ios sets is about 50ms, that is a little too fast for me, so i want to change the connection interval...
