Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
We have a well-vetted software environment what uses SDK 15.3.0 and softdevice s132. We are considering adding ANT+ to our environment, which as I understand requires that...
Hello,
I am working on nRF52832 board and I wanted to implement fixed passkey feature. But, when I am setting
CONFIG_BT_FIXED_PASSKEY =y
and
bt_conn_cb_register...
Hello ,
i am trying to find out advertisement handler while SD advertising in SYSTEM ON mode.
i have added a simple counter to see if it is increasing or not but it is...
Hello fellow developers!
I am currently working on a scale application using the nRF52 DK, and I've run into a roadblock regarding the integration of the HX711 load cell...
Good morning,
I would like to know if I can work with Zephyr with C++ and how to do it.
development software, with versions:
Windows 11
nRF52840-DK PCA10056, 3...
Hello
I'm suing the smp_svr sample from the Zephyr SDK 2..6.1
I want to change the CONFIG_MCUBOOT_IMAGE_VERSION to force the OTA DFU ( over bluetooth ) but when I add...
Hello Nordic Team,
I am writing because I encountered an issue while developing a BLE application on the nRF5340 development board. Currently, I have set up this callback...
With multiple of the provided samples with the SDK, I'm getting a repeated build loop that ultimately fails due to a remaining "dirty build.ninja". This is primarily with...
Hi,
I am working BT840F which has nrf52840, I am using ble_app_uart example to transfer UART data to app. I wanted to know what is the system frequency of the microcontroller...
Hi,
I am using an external flash on the NRF52840DK via SPI and have established working communication with the flash memory. However, I need to disable CONFIG_SPI...
In my project, using nrf52840 controller, I am trying to store 253 bytes of data in NVM, but I encounter an error: "flash_nrf: invalid address: 0x00100ff8:8." Is there any...
Hello DevZone,
I'm porting my project from NCS 2.5.0 to NCS 2.7.0.
I know that there are lots of changes in build system, especially in Zephyr sysbuild. So, I decided...
Hello, I was able to update nRF Connect SDK to v2.7.0 fine using nRF Connect for Desktop. However, the nRF Connect for VS Code extension update v2024.7.13 causes VS Code launch...