I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello, I have a couple of questions concerning the nrf52840 dongle
1. Is the dongle supported in the nrf connect sdk? I see that the board is within the build boards,...
Hi Sir
I am using an example from NCS 2.6.0 and want to modify it to use ADC channel 6 (P0.30) to read voltage values, but I am unable to get the correct values. (When I...
Hi, I have a custom board connected with DK and i was able to program it and test some simple codes. I need to test this TWI example on my board. I uploaded it but i am not...
I am currently developing with the nRF52832 using the nRF5 SDK 14.2 and need to proceed with AES-128 encryption.
However, I cannot find the CDC (Cipher Block Chaining) library...
I'm using nRF Connect SDK version 2.3.0 nrf52840, and external flash - W25Q256JVEIQ. I believe I'm running the chip at 80MHz (rated for 133), with the qspi chip and partition...
OS: Windows
Name: nRF Connect for VS Code Version: 2023.11.301
Found an issue with saving the preset file (Save configuration as preset) when project is located on a...
I'm using an nRF52840 and SDK 15.2 (although I can go to hardware directly if required).
What I want to do is to set a pin as an output with a normal drive run high on...
Hi,
Today I'm trying to run a Thread application on an nRF5340, using the secure environment (not ns). Building the firmware as ns is fine and works as expected, but when...
Hi,
I tried running the \zephyr\samples\bluetooth\periodic_adv program as a host-only application on the nrf52840 development board, with the controller using an nrf52832...
We are working on an idea for a protocol with very low latency events for multiple devices.
For this we would like to be able to transmit a packet only when no other transmitter...
Hello Nordic,
We are currently working on a project that involves communication between Main MCU and a Nordic BLE. From the documents i found that, we can use SPI or UART...
Hello. Are there any plans to officially port the nRF91 series or any other nRF MCU to Arduino for quick prototyping and cross platform compatibility? That would be very useful...
Hello Experts,
I am using nRF52833 / PCA10100 DK boards with SDK nRF5SDK160098a08e2. ( legacy product has the same so no plans to go to Zephyr )
In this SDK there are...
Hello,
I'm encountering an issue while configuring the SPI bus to communicate with a LIS3DH sensor using nrf52832. I'm working with Visual Studio Code using nrfConnect SDK...
Hi
I'm using the nrf52840DK and this example: "BLE Fundamentals, Lesson 4, Exercise 3," where you can send/receive strings between UART and Bluetooth. This works perfectly...
