Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
When I was developing a keyboard using the nRF52840 with the NCS SDK, I found that the keyboard couldn't type on macOS when connected via USB or BLE. However, it worked perfectly...
NCS 2.7.0, NRF52840, SYSBUILD with MCUBOOT
We have 1 specific board which is failing with a hardfault and assert MPSL ASSERT: 112, 1617 it occurs whenever we activate...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hello,
I am developing a Zigbee switch based on the nRF54L15. One of the mandatory features is transitioning into sleep mode when the device is not in use. I thought I had...
Hello everyone,
I get an error when building my vscode NRF5340 project on macOS:
ImportError: dlopen(/Users/lekimtinh/Library/Python/3.9/lib/python/site-packages/_cffi_backend...
Hello !
Time to evaluate and migrate to NRF54...
1.
Does latest nRF52 Connect SDK have sample for HCI interface with Bluetooth Controller ?
I would like to connect...
Dear all,
I'm developing a 1 VS 4 BLE connection system, using 1 nRF52840 as BLE central and 4 nRF52832 as BLE peripherals.
I'm trying to send the same command to 4 peripherals...
Good Day,
We build a custom board with nrf5340 & nrf21540,
NetCore DTS (below) , NetApp DTS has the gpio_fwd in place , all looks good in .config generated. Net-core UART0...
Hi,
I've been trying to set up UART communication with external device using uart3 instance and have so far failed.
The scenario requires sending 5 bytes to the device...
Hi!
I'm trying to portnRF7002 QSPI bus driver for one of the NXP MCUs. Communication with nRF7002 under Zephyr is already established and everything works as expected. ...
Hi
I compiled an older project using embedded studio and flashed my NRF dongle. Now the USB DFU bootloader seems to be gone.
How can I restore it?
Several links on devzone...
Hi
I am using hci_pwr_ctrl and want to get the RSS (read_conn_rssi(default_conn_handle, &rssi) in a very high frequency. However, I notice when I use 100Hz frequency, a...
HI there,
I've been following the DevAcademy Lesson 5 exercise example on SPI communication to get a nRF9161 DK (as a Master) and an ESP32 (as a Slave) to communicate synchronously...
