Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
I develop a test fixture based on nrf51 code that I use for final product.
NRF51 is just a part of a complex test fixture, then I have just "one" test fixture model.
I...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?
I'm developing a Bluetooth mesh device on a Window 10 machine using Segger Embedded Studio v4.52c on a nRF52832 chip using SDK16.0.0, Mesh SDK 4.1.0 and FreeRTOS.
in the...
Dear all.
I just got nRF52 DK and testing blinky based on KEIL and it works well.
I tried one test, IF BOOT/Reset, and nRF52 PDK is not working after below sequence. ...
Would it be possible at all to add a preset text string to the current advertising data, in an advertising-only module configuration, by changing the logical input of one...
Hi,
I've upgraded my SDK from 15.2 to 17.
After upgrading - I can't connect my device via NFC - it keeps disconnect with NRF_ERROR_RESOURCES .
I've tried to increase...
Hi
My goal is to create a USB HCI firmware that works on any custom board that exposes the USB port of a nRF52840. Based on the requirement for USB HCI it was clear to use...
Hi, I am working on an OTBR, nrf52840 connects to the router through SPI, I want to know how to upgrade 52840 through the router. The router use OpenWRT. p lease give me some...
Hi,
Our devices are getting randomly bricked by updating firmware through mcumgr in Zephyr. It happens on both the nRF91 and nRF52 chips when we run the latest nRF Connect...
It's strange, My nrf52840 can't boot up after power on,unless it was connected to JLINKRTTVIEW, If I disconnected the JLINKRTTVIEW, the device will stop running, Connect again...
Can anyone tell or give a pointer to info about RFCOMM vs. NUS (or any other vendor specific UART emulation service)?
Why are there vendor specific UART emulation services...
Referring to the Nordic message sequence chart in the following link:
https://infocenter.nordicsemi.com/index.jsp
(Software Development Kit -> Previous Versions of nRF5...
Hello!
I use SDK v17 and using the library and example code for the lsm9ds1 sensor.
github.com/.../nRF52-DK-and-LSM9DS1
'lsm9ds1_reg.c', 'lsm9ds1_reg.c' these two files...
Hello!
I am using ble adc scan mode example and successfully tested it with nrfconnect by sending my data from AIN3 . Now i want to send data of ble to raspberry pi bluetooth...
