Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
NCS 2.7.0, NRF52840, SYSBUILD with MCUBOOT
We have 1 specific board which is failing with a hardfault and assert MPSL ASSERT: 112, 1617 it occurs whenever we activate...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hello,
I am developing a Zigbee switch based on the nRF54L15. One of the mandatory features is transitioning into sleep mode when the device is not in use. I thought I had...
Hello everyone,
I get an error when building my vscode NRF5340 project on macOS:
ImportError: dlopen(/Users/lekimtinh/Library/Python/3.9/lib/python/site-packages/_cffi_backend...
Hello !
Time to evaluate and migrate to NRF54...
1.
Does latest nRF52 Connect SDK have sample for HCI interface with Bluetooth Controller ?
I would like to connect...
Dear all,
I'm developing a 1 VS 4 BLE connection system, using 1 nRF52840 as BLE central and 4 nRF52832 as BLE peripherals.
I'm trying to send the same command to 4 peripherals...
Good Day,
We build a custom board with nrf5340 & nrf21540,
NetCore DTS (below) , NetApp DTS has the gpio_fwd in place , all looks good in .config generated. Net-core UART0...
Hi,
I've been trying to set up UART communication with external device using uart3 instance and have so far failed.
The scenario requires sending 5 bytes to the device...
Hi!
I'm trying to portnRF7002 QSPI bus driver for one of the NXP MCUs. Communication with nRF7002 under Zephyr is already established and everything works as expected. ...
Hi
I compiled an older project using embedded studio and flashed my NRF dongle. Now the USB DFU bootloader seems to be gone.
How can I restore it?
Several links on devzone...
Hi
I am using hci_pwr_ctrl and want to get the RSS (read_conn_rssi(default_conn_handle, &rssi) in a very high frequency. However, I notice when I use 100Hz frequency, a...
HI there,
I've been following the DevAcademy Lesson 5 exercise example on SPI communication to get a nRF9161 DK (as a Master) and an ESP32 (as a Slave) to communicate synchronously...
Is there any othere way than mergehex to merge application core and netcore hex files? I'm not sure if I'm following correctly, but it seems like it might be possible through...
I would like some help with porting the modem library (nrf_modem_lib) to work with my bare metal application. Besides a custom nrf_modem_os.c, I have made a slightly modified...
