Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
Hello, I' needing some help on setting up the MCUBoot for the BL5340PA using the ncs 2.6.2. Currently I have the below add on for the prj.conf for the application core:
...
I would like to implement ble mesh direct forwarding feature in my code but i am not finding zephyr library for that. Is there any possibility to get link for zephyr direct...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
Hi All!
Hope you are doing well!
I am using nrf52833, NCS 2.3.0, Want to minimize the current consumption by sleep mode.
For this, I disabled the UART and SPI and the...
Hi
I have been studying the nRF Connect SDK and taking the courses at Nordic Dev Academy. In the Zephyr Fundamentals course, as I don't have the sensors used in lesson 6...
hello.
We're now planning to migrate our firmware library from nrf5 sdk 17.1.0 to stand alone nrfx v3.xx.x.
All our products are made with nrf5 sdk 17.1.0 using ses. ...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
I'm working with the nRF7002DK board using NCS version 2.6.0 . The internal flash is full, so I need to perform BLE DFU using external flash. Is there a sample available for...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
How can this be done?
calls to bt_id_reset, and bt_id_delete do not work on the BT_ID_DEFAULT.
I wish for the device to appear as a different device (IRK) each time it...
