Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hello Nordic Support Team,
We are developing a custom product based on the Nordic nRF54L15-CAAA(R) SoC.
Our project requirement is to use the nRF Connect SDK Bare Metal...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hi Technical Support, We are using nRF54 series with NCS v3.0.0, and we have encountered a low power anomaly as described below: Configuration: SoC: nRF54 series NCS: v3.0...
Hi,
I would like to know how to ensure that AP-protect is disabled for application based on 17.1.0 nRF5 SDK.
I've understood that the procedure is:
1. recover the device...
We are designing an nRF52840 (Ebyte E73-2G4M08S1C module) into a battery-powered wearable, USB device only, Full-Speed, sink-only Type-C with 5.1 kΩ Rd on both CC pins. We...
I'm starting an investigation into Bluetooth LE Channel Sounding using the nRF54L15 Tag, nRF54L15-DK, and nRF54LS05-DK.
For the intended product, I need approximately 150...
We have a product in the field using the NRF9160 and AWS IOT MQTT from NRF Connect SDK 3.1.1. It is always connected when awake (power cycle controlled by an external micro...
Hello,
We use the nPM2100 EK for getting familiar with nPM2100 for its potential use in our project where we aim to use single AAA battery for powering it.
Our usage profile...
Hallo，
What’s the purpose of connecting an 820pF capacitor to the DEC5 pin on the nRF52840 hardware versions before Fxx? For the chips shipped later, will the version be...
Hi
I have custom nrf5340 based product, with an NFC interface for card emulation. I have managed to get this to work in raw APDU mode in NCS 2.9.0 (with selected cherry...
Hi, We've been investigating the use of the nrF54LM20B with the integrated Axon NPU. In order to gauge the Axon's effectiveness, we've constructed a benchmark that profiles...
1. Stack ANT_s212_nrf52810_nrf52832_6.1.1, tried disabling all peripherals and only running the following code, GPIO toggles every 20s, occurs after running for a while. int...
I am curious about the RF pin impedance, as this parameter is not listed in the relevant specification for nRF54 SoC family (i.e. datasheet v1.0).
I wonder whether it is...
