Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hello,
I recently purchased a Nordic Thingy 91 device, and I have been working on it for a few weeks. I am currently experiencing two major issues with the kit that are...
Hi,
I have a board which is nrf9151 with nrf52840 as BLE controller connected via hci_lpuart. This works fine so far, I am able to do simple AT commands as well as doing...
when I try to add a build config, i can only see a blank page for build configs.
but if i click on another project's build config which is already created, i can see the...
Hi,
I'm troubling using the retention module of Zephyr with NCS 2.6.1 on an NRF52840. I've read the Retention System Documentation of Zephyr but it is not working for me...
Folks,
Am running VSC 1.95.1 on Mageia Linux.
I have a 52833 board that I have working in that I can write to and read from custom BLE characteristics and send data out...
Hi
I'm setting up an OpenThread network and am trying to use the nRF Thread Topology Monitor to visualize the network for debugging purposes. However, no OT devices appear...
According the AT command documentation, reading the device certificate is not supported.
That's somehow irritating. There is no reason for that, at least for those who common...
Hello,
My board contains nRF9160 and nRF52840. The nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with nRF52840 over UART. I want to perform...
Hi, in our project we use nRF5340 to control some externanal peripherals as flash mem through SPI and also we need BLE comunication.
The case is if whe allow the config...
Hi, I am trying to use the DECT NR+ sample from the 2.7.0 nrfconnect sdk but I can't seem to get the following to work in the prj.conf:
the results of my build give...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
Can the VDD PIN of 4L15 be used to detect the ADC voltage? VDD is powered by a dry battery (3.2V~1.8V), LED+ is powered by 3.3V, LED- will be connected to the I/O of the 54L15...
