i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Dear Nordic Engineers
I would like to sample the ADC between advertisements or connections, that is when the RF is sleeping, so I want to use Timeslot, I see there is a...
I am trying nrf52840. The conditions are as follows. -The development environment is SEGGER. -nRF5_SDK_17.1.0 -The evaluation board is a DK from Raytac. There are two identical...
Hello,
I'm starting a new project on a NRF52810, and i need to use the pairing feature in my application. As a result i need to compile the FDS driver. If i'm doing so,...
Hello,
I have setup a single master and multiple slaves (10 in number).
The master has master TX channel and the slaves have slave RX channels.
The slaves send data...
Hi, I am working on ble_app_uart_c_pca10056_s140 project. I have changed the following for power saving. Is this the right way to achieve this mode? After how much time it...
I used this code to convert my analog sensor data to digital with 5 khz continuous sampling and after that i want to sent my data to pc via BLE. In this code, NUS was used...
I'm using a custom battery operated board with the nRF52840, when there is no GPIO events for a specified time period, the device goes to a hibernate mode using the __WFE...
I am currently working with a dvk-bl653 working on increasing the speed of the DFU. I have a max packet size of 251 and have tried different connection intervals but only...
Hi again
I have used nrfConnect to create an application from sample, the sample being peripheral_hr_coded
I have placed my custom service into the app, and it works...
Hello, I am trying to measure the input voltage on an nRF52833 and it is not behaving as expected.
The following code is taken from here and works as expected on any nRF52832...
Dear Sir.
I am using the cJSON driver .
When it comes to string it works fine .
However when I use integer and swap the lines
//cJSON_AddStringToObject(root, ...
I'm sorry my English is not good enough.
I am developing a product that works as a BLE peripheral using nrf52832 and NCS1.6.1.
In addition, the following statement is...
Hello,
I am trying to establish a mesh network with two nodes(self provisioned) simulating the Light and Light_switch examples without the provisioner. My plan is to play...
Fairly new to nRF Connect SDK & Zephyr although I have worked a lot with NRF5 SDK
I'm at a bit of a dead end here. I trying to setup a way to repeatedly read out data from...
Hello,
I would like to use littlefs in out Project and it seems to be very usefull. I read several documents and have the sample running on the eval board. But there is...
