hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hell there Can I find an SDK that is supported on Nrf52805 chip? Or can I get any proper guidance on program of nrf52805 (the module MS46SFIi) together with Segger Studio...
For regional compliance testing, I am seeking an older version of the Direct Test Mode PC application, specifically v2.0.2 . Is there a way to get old versions of this application...
Hey everyone,
I’ve been banging my head against an issue with my custom nRF54L15 board , and I’m under a bit of pressure to get five samples working. Unfortunately, the...
What is the tolerance of the 0.9V internal reference used by the nrf54L15 SAADC (+/-10%?, +/-1%?), and what is the maximum external reference voltage allowed?
I am using Windows 11, NCS v2, VSCode extension, under WSL2.
What I want to do is build a UF2 image of my zephyr application and be able to drag/drop it onto a bootloader...
Hello Nordic Support Team,
We are developing a custom product based on the Nordic nRF54L15-CAAA(R) SoC.
Our project requirement is to use the nRF Connect SDK Bare Metal...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hi Technical Support, We are using nRF54 series with NCS v3.0.0, and we have encountered a low power anomaly as described below: Configuration: SoC: nRF54 series NCS: v3.0...
Hi,
I would like to know how to ensure that AP-protect is disabled for application based on 17.1.0 nRF5 SDK.
I've understood that the procedure is:
1. recover the device...
We are designing an nRF52840 (Ebyte E73-2G4M08S1C module) into a battery-powered wearable, USB device only, Full-Speed, sink-only Type-C with 5.1 kΩ Rd on both CC pins. We...
I'm starting an investigation into Bluetooth LE Channel Sounding using the nRF54L15 Tag, nRF54L15-DK, and nRF54LS05-DK.
For the intended product, I need approximately 150...
We have a product in the field using the NRF9160 and AWS IOT MQTT from NRF Connect SDK 3.1.1. It is always connected when awake (power cycle controlled by an external micro...
Hello,
We use the nPM2100 EK for getting familiar with nPM2100 for its potential use in our project where we aim to use single AAA battery for powering it.
Our usage profile...
