Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
We have a well-vetted software environment what uses SDK 15.3.0 and softdevice s132. We are considering adding ANT+ to our environment, which as I understand requires that...
I am in the process of bringing up a custom board with an nrf5340 and a FUSB302B USB-C PHY-controller.
As a driver for the FUSB203B, I am using this project as an OOT-module...
Hello
Due to some reasons we need to use external antenna and RF cables.
What is a part number of the antenna that can be connected to the J1 RF Antenna connector?
We...
Hi,
I am implemented the uart functionality, I'm getting below issue.
[00:00:00.445,526] <err> Throughput: Failed to set UART callback (err -88) [00:00:00.445,556] <err...
I want to use LPCOMP in nrf52832 to detect a rising edge of voltage. And my code is:
I set the reference as NRF_LPCOMP_INPUT_1 or NRF_LPCOMP_REF_SUPPLY_4_8, the event is...
I am running on openthread demo: ot_cli on its low power mode by building with low_power snippet.
As document says, it will automatically suspend UART operation when low...
Hi,
I'm trying to use to gpio pins in order to wake up a system from sleep mode.(PIN1= P0.24 PIN2 =P1.1 )
If I use the GPIOTEs separately in my project, it works and sytem...
There are some serious issues in the file "board.c" that relate to LEDS_NUMBER.
If I create a custom board with no LEDs then I set LEDS_NUMBER to in my custom boards,h....
Hello,
My company has developed a Bluetooth application that runs on the nRF52832 and we are about to perform FCC pre-scan testing next week. In order to prepare for this...
I want to use one device (nrf5340 audio DK) as both a gateway and a headset. Is this possible?
It needs to both receive audio from a CIS gateway and send it out, working...
Hi Team, I need to integrate FreeRTOS into the ble_app_hrs_nfc_pairing example. What are the ways to integrate FreeRTOS into ble_app_hrs_nfc_pairing? I need to create two...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
I am aiming to connect the Gateway and Headset 1:1 and output stereo from the Headset.
The Gateway side is 16-bit I2S and the Headset side is 32-bit I2S, and I am able to...
Hi, I have an issue I can't understand. I'm getting the TRICKLETIMEOUT (Trickle timer timeout) ERROR 64 from my nPM1300.
If I understand correctly:
1. Trickle charging...
