Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
After upgrading my NCS version from 3.1.1 to 3.2.0 for the nRF54L15, I found that the GRTC resets after a sys_reboot(), whereas it didn't in the previous version. What changes...
Hello everyone. I'm using the nRF52840 Pro Micro board with the J-Link programmer and the nRF Connect extension for VS Code. This board comes with a U2F bootloader, but I...
I use a hardware timer to capture/compare incoming pulses using PPI to trigger the captures from GPIOTE. I previously wrote the same application for nRF52832 on the old SDK...
When running SLM on nrf91, it sends "Ready\r\n" over UART on boot/reset. On nrf54, we use "Ready" to detect reboots and rerun the setup. However, when the modem reboots, sometimes...
Hello Team,
I am using the nrf54l15 custom board for development. I have configured the P1.06 as a normal GPIO as follows:
And using it as follows:
The pin status...
I use example from nrf52 SDK. project path:nRF5 SDK\nRF5_SDK17.1\examples\ble_peripheral\ble_app_uart\pca10040e\s112\arm5_no_packs.
emulator: ST link V2
but no target...
Hello,
The nRF5340 supports audio transmission, while the nRF54L15 supports Channel Sounding. Is it possible to conduct audio transmission simultaneously with Channel Sounding...
We need to use a Lithium Ion battery to power our device and need to connect to a chip that has 1V8 logic levels as its only option.
We're early in development, so it seems...
I am encountering a strange hardware/software mapping issue with the SAADC on an nRF52833 DK running on Zephyr (NCS) . Using VS Code nRF Toolchain and SDK (V3.2)
The issue...
This one gets complicated as I cannot reproduce the problem with my original NRF5340 DK.
Steps to reproduce are trivially easy, but only fail when using my favourite OEM...
Just a quick one as I couldn't find it on google. I'm going to implement a beacon like broadcaster but one not based on location. It'll probably be a uuid, a random identifier...
Hello,
I encountered a problem while trying to bond a nrf54L15 (central) with a nrf52810 (peripheral). The firmware of the nrf54 is using Nordic Connect SDK and the nrf52...
Hello,
I hope you are well.
I have a code inside the connection connected callback that sets the MTU to the maximum, which is working fine on ncs v3.0.2 but generates...
Hi everyone,
I’m currently working with the nRF9151-LACA-A1A-R module, developing NTN communication features using SLM mode. However, I haven’t been able to find any documentation...
"I am using nRF Connect SDK (NCS) v3.1.0 and developed BLE DFU functionality by referencing the Nordic Semiconductor Academy course: ' Exercise 5: FOTA over Bluetooth Low...
