I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I have a Thingy91 that I want to connect to nRFcloud. Not knowing the state of its keys/provisioning I followed the procedure to generate just-in-time keys (as a first attempt...
Hello all!
I'm starting development of BLE Mesh network as part of my Master thesis, for which I designed a custom board based on nRF52832 and nRF52840 with some built-in...
I am working on nrf52840 using nrf connect sdk v2.0.0 example periodic_adv, nrf52840 is prodcasting extended advertising, my app is running on Sony Xperia 1 with bluetooth...
Hello Nordic Community,
I'm now struggeling for quiet some time with trying to get the Keyboard HID example to work with the nRF52840 Dongle.
I already read the complete...
Hi , Nordic and all .
I try to develop uac and hid Composite Device, but i can't find any example about Composite Device in NCS , can't everybody help me .
Thanks very...
Good day
I have been trying to incorporate the WS2812.c from the zigbee lightbulb example (no soft device) with the BLE_Blinky example (with soft device) SDK v 17.2 PCA10059...
Hi. We evaluated the nRF Distance Measurement result with sample 'samples/bluetooth/nrf_dm' of nRF Connect SDK 2.0.0. hardware is two nrf52833dk_nrf52833 board. Below is a...
Hi Nordic,
nRF5 sdk for mesh 5.0, s132, SES
In the mesh network, there are transmitters and receivers. The receivers only receive messages and there are no messages to...
Hey guys,
I am using mesh->provisioner_nrf52840 example flashed in one board, and mesh-> light_switch_server example flashed in another board
I could able to read the...
Hi, I am using an nRF52833dk and my project needs usage of Virtual EEPROM / emulated eeprom over flash memory. I could see that nCS-Zephyr provides a driver at the SDK "v1...
I am trying to build an application where the device scans and on receipt of a packet with certain data in it, advertises for a short while, using both advertising and scan...
I am using NRF SDK 15.2 SDK for development , Im trying scan more beacons ,
static ble_gap_scan_params_t m_scan_param = { .active = 0x01, .interval = 0x0100 , .window =...
Hi,
We have an existing design that includes the nRF52832 and we would like to add the nRF9160 to the design. Does the nRF52832 support coexistence with the nRF9160?
If...
Hello,
We found that the nrf52840 cannot properly pull the CS pin high to get the MX25R64 into DPD. The SDK version is nrf connect SDK V2.0.0. The macro CONFIG_PM_DEVICE...
