I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
The text for the recommended nRF Connect SDK workflow (using a Workspace Application Repository - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/dev_model_and_contributions...
Dear Devzone:
I have setup done matter environment as blow:
NB: Ubuntu 22.04 with WIFI and BT, installed CHIP tool from official pre-built (V2.8.0 corresponding version...
Hello
Our customer makes IoT Product and use the Nordic 9160.
However the PCB Size is small.the 9160 SiP design in the PCB Top layer and Sim Card design in the Bottom...
Hello
As the title says, I am suspending the UART using PM_DEVICE ACTION_SUSPEND, but the power consumption is not decreasing significantly.
With CONFIG_SERIAL=n and no...
Hello. I'm trying to toggle a GPIO pin at a predefined frequency in order to measure the accuracy of out RTC clock. This code uses the GPIOTE, RTC, and PPI peripherals in...
We are evaluating the the NRF 5340 for a new project and we would like to know if the NVS implementation [1] provides protection against data corruption if the supply is unexpectedly...
Hi guys,
So, I've been working on a project for measuring liquid using the TDC1000 IC from TI which was running fine on STM32.
My experience with nordic connect sdk is...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our pre-production PCB power consumption still too high, so we are looking for a way...
Hello, I have a Thingy:53 sensor hub application (extended the Nordic Thingy53 Sensor Hub blog to include IAQ sensor) built under NCS v2.7.0 that runs fine.
When rebuilding...
In the link process between Central and Peripheral,
sometimes Link processing does not work correctly and the following log output: . cis_gateway: Discovery failed: 14 ...
1. After DFU has successfully completed the watchdog fires. I know this because my App picks it up from the register, however I'd like to use this bit to indicate a potential...
Hello,
I am designing a PCB using the nRF54L15 and a ceramic antenna and got confused regarding the impedance-matching network. In the detasheet a 1.5pF, 2.0pF, and 0.3pF...
Hello,
I am using nrf52832 as a peripheral and running SD S132. l am looking for an ble peripheral example wherein the Out of Band security level is used.
Can you point...
Using Programmer v4.0.1 can successfully read the NRF51822AB, but upgrading to the latest version 4.4.2 results in a failure to read the device.
Additionally, after...
We are working with nRF52840 and NCS2.6.1. And we want to change pin configuration for UART1 instance during the runtime and we have also used following ASYNC UART configuration...
