I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi
We have nRF52840 + FEM in our design. Output power level is mainly controlled by the nRF52840 TX power setting which drives the FEM. However, the txpower options is...
Hey, After updating the nRF Connect SDK v2.60 (from 2.3.0) package an attempt to turn a BLE carrier ON by sending the BT_HCI_OP_LE_TX_TEST_v4 DTM command over the HCI interface...
Hi,nordic teams
im develop a keyboard use nrf52840 by ncs sdk 2.6.when i test the dfu funcation by python file ,there is 2 problems .
1.the usb dfu is so slow that i need...
I want to add a custom at command in the SLM example . I follow the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.1/nrf/libraries/modem/at_cmd_custom.html , enable...
Hi.
I have a problem.
I changed project settings 52832 -> 52840
on 52832 the project work perfectly.
using 52832, SDK 15.3.0 S332, ble, ant, ble dfu.
now I wanna...
I use one channel of the SAADC on nRF52832 to measure the power supply voltage. Code for configuration & operation of SAADC attached:
Short description:
- Configure...
Hello and thank you for your time. I seem to be getting some incorrect performance from the flash memory with NVS, in that NVS needs to be primed or something before it works...
Hi,
I'm working on a board that uses an npm1100 (QFN) in the following configuration:
When testing my board, I populated it with only the components shown in the...
Debugging my application indicates that I might be not servicing BLE NUS RX frequently enough bt_nus_cb.received is sometimes not called timely Is there any way for user to...
Hello all,
I'm using a custom nrf52840 dongle. There are some questions about bootloader and Softdevice. Everything works fine when I use nrf Bluetooth Low Energy app...
Hello.
I have a product that I am working on which a peripheral and it is able to communicate test data over BLE UART connection. For development purposes, we have internally...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Gateway and I'm able to achieve it. ( developer.nordicsemi.com/.....
Hi,
We are developing on a nRF52832 MCU and we tried to enable MPU on the whole RAM region (addr: 0x20000000, size : 0x10000) But when we create a new MPU region around...
Hi,
So I have seen there is a clean -up option to set the architecture core HW registers to their warm -reset values as specified by the architecture before running the...
Hello everyone,
using Segger Embedded Studio, I encountered an issue with the TWI libraries. My device consists of a custom PCB controlled by the nRF52840 (programmed with...
